142 lines
6.1 KiB
C
142 lines
6.1 KiB
C
//////////////////////////////////////////////////////
|
|
// First things first, all the includes we need //
|
|
//////////////////////////////////////////////////////
|
|
|
|
#include "hardware.h" // We need the header for this code
|
|
#include "afsk.h" // We also need to know about the AFSK modem
|
|
|
|
#include <cpu/irq.h> // Interrupt functions from BertOS
|
|
|
|
#include <avr/io.h> // AVR IO functions from BertOS
|
|
#include <avr/interrupt.h> // AVR interrupt functions from BertOS
|
|
|
|
// A reference to our modem "object"
|
|
static Afsk *modem;
|
|
|
|
//////////////////////////////////////////////////////
|
|
// And now for the actual hardware functions //
|
|
//////////////////////////////////////////////////////
|
|
|
|
// This function initializes the ADC and configures
|
|
// it the way we need.
|
|
void hw_afsk_adcInit(int ch, Afsk *_modem)
|
|
{
|
|
// Store a reference to our modem "object"
|
|
modem = _modem;
|
|
|
|
// Also make sure that we are not trying to use
|
|
// a pin that can't be used for analog input
|
|
ASSERT(ch <= 5);
|
|
|
|
// We need to do some configuration on the Timer/Counter Control
|
|
// Register 1, aka Timer1
|
|
// The following bits are set:
|
|
// CS11: ClockSource 11, sets the prescaler to 8, ie 2MHz
|
|
// WGM13 and WGM12 together enables Timer Mode 12, which
|
|
// is Clear Timer on Compare, compare set to TOP, and the
|
|
// source for the TOP value is ICR1 (Input Capture Register1).
|
|
TCCR1A = 0;
|
|
TCCR1B = BV(CS11) | BV(WGM13) | BV(WGM12);
|
|
|
|
// Then we set the ICR1 register to what count value we want to
|
|
// reset (and thus trigger the interrupt) at.
|
|
// Since the prescaler is set to 2MHz, the counter will be
|
|
// incremented two million times each second, and we want the
|
|
// interrupt to trigger 9600 time each second. The formula for
|
|
// calculating the value of ICR1 (the TOP value) is:
|
|
// (CPUClock / Prescaler) / desired frequency - 1
|
|
// So that's what well put in this register to set up our
|
|
// 9.6KHz sampling rate.
|
|
ICR1 = ((CPU_FREQ / 8) / 9600) - 1;
|
|
|
|
// Set reference to AVCC (5V), select pin
|
|
// Set the ADMUX register. The first part (BV(REFS0)) sets
|
|
// the reference voltage to VCC (5V), and the next selects
|
|
// the ADC channel (basically what pin we are capturing on)
|
|
ADMUX = BV(REFS0) | ch;
|
|
|
|
DDRC &= ~BV(ch); // Set the selected channel (pin) to input
|
|
PORTC &= ~BV(ch); // Initialize the selected pin to LOW
|
|
DIDR0 |= BV(ch); // Disable the Digital Input Buffer on selected pin
|
|
|
|
// Now a little more configuration to get the ADC working
|
|
// the way we want
|
|
ADCSRB = BV(ADTS2) | // Setting these three on (1-1-1) sets the ADC to
|
|
BV(ADTS1) | // "Timer1 capture event". That means we can declare
|
|
BV(ADTS0); // an ISR in the ADC Vector, that will then get called
|
|
// everytime the ADC has a sample ready, which will
|
|
// happen at the 9.6Khz sampling rate we set up earlier
|
|
|
|
ADCSRA = BV(ADEN) | // ADC Enable - Yes, we need to turn it on :)
|
|
BV(ADSC) | // ADC Start Converting - Tell it to start doing conversions
|
|
BV(ADATE) | // Enable autotriggering - Enables the autotrigger on complete
|
|
BV(ADIE) | // ADC Interrupt enable - Enables an interrupt to be called
|
|
BV(ADPS2); // Enable prescaler flag 2 (1-0-0 = division by 16 = 1MHz)
|
|
// This sets the ADC to run at 1MHz. This is out of spec,
|
|
// Since it's normal operating range is only up to 200KHz.
|
|
// But don't worry, it's not dangerous! I promise it wont
|
|
// blow up :) There is a downside to running at this speed
|
|
// though, hence the "out of spec", which is that we get
|
|
// a much lower resolution on the output. In this case,
|
|
// it's not a problem though, since we don't need the full
|
|
// 10-bit resolution, so we'll take fast and less precise!
|
|
}
|
|
|
|
|
|
// This declares the Interrupt Service routine that will
|
|
// get called everytime the ADC finishes taking a sample.
|
|
// What actually happens here is that we take a piece of
|
|
// code, store it somewhere in memory, and then put the
|
|
// address of that "somewhere" into the Interrupt Vector
|
|
// Table of the processor, in this case the position
|
|
// "ADC_vect". This lets the processor know what to do
|
|
// when all the timing and configuration we just set up
|
|
// finally* ends up triggering the interrupt.
|
|
bool hw_afsk_dac_isr;
|
|
DECLARE_ISR(ADC_vect) {
|
|
TIFR1 = BV(ICF1);
|
|
|
|
// Call the routine for analysing the captured sample
|
|
// Notice that we read the ADC sample, and then bitshift
|
|
// by two places to the right, effectively eliminating
|
|
// two bits of precision. But we didn't have those
|
|
// anyway, because the ADC is running at high speed.
|
|
// We then subtract 128 from the value, to get the
|
|
// representation to match an AC waveform. We need to
|
|
// do this because the AC waveform (from the audio input)
|
|
// is biased by +2.5V, which is nessecary, since the ADC
|
|
// can't read negative voltages. By doing this simple
|
|
// math, we bring it back to an AC representation
|
|
// we can do further calculations on.
|
|
afsk_adc_isr(modem, ((int16_t)((ADC) >> 2) - 128));
|
|
|
|
// We also need to check if we're supposed to spit
|
|
// out some modulated data to the DAC.
|
|
if (hw_afsk_dac_isr)
|
|
// If there is, it's easy to actually do so. We
|
|
// calculate what the sample should be in the
|
|
// DAC ISR, and apply the bitmask 11110000. This
|
|
// simoultaneously spits out our 4-bit digital
|
|
// sample to the four pins connected to our DAC
|
|
// circuit, which then converts it to an analog
|
|
// waveform. The reason for the " | BV(3)" is that
|
|
// we also need to trigger another pin controlled
|
|
// by the PORTD register. This is the PTT pin
|
|
// which tells the radio to open it transmitter.
|
|
PORTD = (afsk_dac_isr(modem) & 0xF0) | BV(3);
|
|
else
|
|
// If we're not supposed to transmit anything, we
|
|
// keep quiet by continously sending 128, which
|
|
// when converted to an AC waveform by the DAC,
|
|
// equates to a steady, unchanging 0 volts.
|
|
PORTD = 128;
|
|
}
|
|
|
|
|
|
// * "finally" is probably the wrong description here.
|
|
// "All the f'ing time" is probably more accurate :)
|
|
// but it felt like it was a long way down here,
|
|
// writing all the explanations. I think this is a
|
|
// nice testament to how efficient and smart these
|
|
// processors are. The actual code to set up what
|
|
// took a long time to explain, is really very short.
|