Merge branch 'master' into master

This commit is contained in:
markqvist 2024-05-18 10:26:10 +02:00 committed by GitHub
commit 30fb26e1a8
No known key found for this signature in database
GPG Key ID: B5690EEEBB952194
5 changed files with 42 additions and 15 deletions

View File

@ -79,6 +79,7 @@
#define HAS_EEPROM false
#define HAS_INPUT false
#define HAS_SLEEP false
#define PIN_DISP_SLEEP -1
#define VALIDATE_FIRMWARE true
#if defined(ENABLE_TCXO)
@ -353,11 +354,13 @@
#define HAS_SD false
#define HAS_EEPROM true
// #define HAS_INPUT true
// #define HAS_SLEEP true
// #define PIN_WAKEUP GPIO_NUM_0
// #define WAKEUP_LEVEL 0
// const int pin_btn_usr1 = 0;
#define HAS_INPUT true
#define HAS_SLEEP true
#define PIN_WAKEUP GPIO_NUM_0
#define WAKEUP_LEVEL 0
// #define PIN_DISP_SLEEP 21
// #define DISP_SLEEP_LEVEL HIGH
const int pin_btn_usr1 = 0;
const int pin_cs = 7;
const int pin_reset = 8;

View File

@ -564,7 +564,15 @@ void update_disp_area() {
}
}
void update_display() {
void update_display(bool blank = false) {
if (blank) {
if (display_contrast != display_intensity) {
display_contrast = display_intensity;
set_contrast(&display, display_contrast);
}
display.clearDisplay();
display.display();
} else {
if (millis()-last_disp_update >= disp_update_interval) {
if (display_contrast != display_intensity) {
display_contrast = display_intensity;
@ -576,6 +584,7 @@ void update_display() {
display.display();
last_disp_update = millis();
}
}
}
void ext_fb_enable() {

View File

@ -176,11 +176,17 @@ upload-rnode_ng_21:
python ./Release/esptool/esptool.py --chip esp32 --port /dev/ttyACM0 --baud 921600 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 80m --flash_size 4MB 0x210000 ./Release/console_image.bin
upload-t3s3:
@echo
@echo Put board into flashing mode by holding BOOT button while momentarily pressing the RESET button. Hit enter when done.
@read
arduino-cli upload -p /dev/ttyACM0 --fqbn esp32:esp32:esp32s3
@sleep 2
python ./Release/esptool/esptool.py --chip esp32s3 --port /dev/ttyACM0 --baud 921600 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 80m --flash_size 4MB 0x210000 ./Release/console_image.bin
@echo
@echo Press the RESET button on the board now, and hit enter
@read
@sleep 1
rnodeconf /dev/ttyACM0 --firmware-hash $$(./partition_hashes ./build/esp32.esp32.esp32s3/RNode_Firmware.ino.bin)
@sleep 3
python ./Release/esptool/esptool.py --chip esp32s3 --port /dev/ttyACM0 --baud 921600 --before default_reset --after hard_reset write_flash -z --flash_mode dio --flash_freq 80m --flash_size 4MB 0x210000 ./Release/console_image.bin
upload-featheresp32:
arduino-cli upload -p /dev/ttyUSB0 --fqbn esp32:esp32:featheresp32

View File

@ -77,7 +77,8 @@ void setup() {
fifo_init(&serialFIFO, serialBuffer, CONFIG_UART_BUFFER_SIZE);
Serial.begin(serial_baudrate);
#if BOARD_MODEL != BOARD_RAK4631
#if BOARD_MODEL != BOARD_RAK4631 && BOARD_MODEL != BOARD_RNODE_NG_22
// Some boards need to wait until the hardware UART is set up before booting
// the full firmware. In the case of the RAK4631, the line below will wait
// until a serial connection is actually established with a master. Thus, it
@ -1311,6 +1312,14 @@ void loop() {
void sleep_now() {
#if HAS_SLEEP == true
#if BOARD_MODEL == BOARD_RNODE_NG_22
display_intensity = 0;
update_display(true);
#endif
#if PIN_DISP_SLEEP >= 0
pinMode(PIN_DISP_SLEEP, OUTPUT);
digitalWrite(PIN_DISP_SLEEP, DISP_SLEEP_LEVEL);
#endif
esp_sleep_enable_ext0_wakeup(PIN_WAKEUP, WAKEUP_LEVEL);
esp_deep_sleep_start();
#endif

Binary file not shown.