Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Specifications:
* SoC: Qualcomm Atheros AR9344 (560 MHz)
* RAM: 64MB
* Storage: 8 MB
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
* aredn: hAP ac lite enable 5GHz LAN Access Point
enable ability to bridge LAN physical ports with wireless
LAN Access Point capability. On dual band hAP ac lite,
used in parallel with mesh RF on 2GHz. Enables future
features on single band devices to turn off mesh RF and
repurposed for mesh LAN Access Point.
closes: #215
Add support for the hAP lite model rb952UI-5ac2nD equivilent to
the UBNT AirRouter. The 5Ghz interface will be configured in a
2nd phase. This hAP lite model has double the RAM and Flash
of the AR. the 2Ghz is MIMO (5Ghz is single antenna).
Once the PR for this is accepted by Openwrt we will need to remove the file
001-add_support_for_TP-Link_CPE510_v2.patch
Removed 001-add_support_for_TP-Link_CPE210_v2.patch as PR #937 has been committed
Updated 99_setup_aredn_include to remove unused Rssi Led configuration
Move httpd.conf to not store password and instead depend on the shadow password file.
Also tag the 40_aredn_migrate-httpdconf script to be +x. Not strictly necessary but wish to have this standard
Change-Id: I018d9a3294e45af2316b3c3947ef2a7d8081268b
Not getting much debug information at moment, would like to put this in uci-defaults but with issues that I can't seem to log at moment (and not having serial cable for this device) I'm going with lets put it in /etc/init.d/local before nvram and similar gets set.
ref AREDN->ticket:115
Old code would set mac on the sub-vlan not the master interface which could cause issues.
Rework to be more functional in the future and to work correctly on vlan interfaces.
ref AREDN->ticket:115
wifi detect is called in /etc/init.d/boot before uci_apply_defaults is called.
Because of this if we don't have the data about the radio0path we need to remove the wifi config file first before calling wifi detect.
Needs to be in uci-defaults to be sure these data sets execute BEFORE the OS boots
We also need to get radio0 path because its mandatory for wifi to work.
Needed for sysupgrade from 3.0.2 to latest version.
Remove setting RF channel on first boot in uci-defaults.
This should allow the node to use standard wifi channels when it boots allowing mesh setup to be run from a laptop or mobile device.
We will later move them to a real mesh channel during the mesh setup page.
Should also resolv issue where nodes were booting up on channel -2 and similar and wifi would refuse to start due to regdomain.
Includes band/channel mapping
Code to set default RF channel on first boot
Add many 5ghz Ubiquiti devices in a testing phase including:
NanoBeam M5 (Intl), NanoBridge M5, AirGrid M5 HP, AirGrid M5, NanoStation M5, NanoStation Loco M5, Bullet M5, Rocket M5
see BBHN->ticket:29
dman776