in the past nodes could be configured uniquely for
a given mode: ap, wifi client, mesh. Current behavior
in basic setup no longer has unique modes, rather wireless
cards can be configured in different modes in basic setup
and devices with multiple wireless interfaces can
be setup to use multiple modes at the same time.
fixes#533fixes#535
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
catch the tunnel comment field in perlfunc's read_post_data function where certain characters are changed to the html character entity in order to not interfere with the config files.
Tested with all kinds of crazy charcters such as: zdsfkh? <!@#$%^&*()> "quote"
Fixes#515
Specifications:
* SoC: Qualcomm Atheros AR9344 (560 MHz)
* RAM: 64MB
* Storage: 8 MB
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
TP-Link CPE610-v2 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
Based on the same underlying hardware as the TP-Link CPE510
Power, LAN0, WLAN green LEDs
23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector
Flashing instructions:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron apcameron@softhome.net
* enhancement: added contact info/comment field for each tunnel connection.
Allows for a short comment or an email address so you can remember who to contact for each tunnel.
The field is optional and does not need to be filled out to get a tunnel connection up.
Also cleaned up some of the layout on the tunnel pages and hopefully made it a bit easier to tell what is what.
Fixes#457
* added `maxlength='50'` to the comment/contact field.
50 characters should be enough for an email address or a short comment.
* Allow for spaces in the Tunnel contact/comment field
This adds support for a popular low-cost 5GHz N based AP
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
Mesh status will show service entries of a remote mesh
node at the top with 0 ETX value. The owning mesh hostname
displays blank across the mesh network.
The root cause is OLSR not propagating the node's hostname due
to the admin assigning a conflicting/duplicate hostname. These
services will no longer show in mesh status.
* Add experimental support for the GL.iNet GL-AR150 - https://openwrt.org/toh/gl.inet/gl-ar150
Mesh networking and tunneling have been confirmed working.
This device has been confirmed capable of operating on channel -1, but /etc/config/wireless has to be manually edited to select this channel.
* www/cgi-bin/perlfunc.pm patched to add UI support for the GL.iNet GL-AR150
* www/cgi-bin/perlfunc.pm patched to add UI support for the GL.iNet GL-AR150 - seems like only 18 dBm TX power is possible
* Remove Experimental comments and designate as stable
* Configure Ethernet ports & VLANs for GL-AR150, and update README.md
* Fix misunderstanding re README.md
* Patch Upstream OpenWRT GL-AR150 LAN & WAN LED mapping, configure WLAN LED as mesh linked indicator.
* sysinfo.json additions
lua library additions
Dependent on #389 and #391
Replaces #387
* additional check for nil needed
tested on a node with several very marginal RF links (IP, no host name) and it is working, so far.
also removed the decimal point on the n/lq values, we didn't need 10 places of accuracy. :)
* a couple more small changes
* changed neighborLinkInfo() function in aredn.info to show *all* links, not just RF.
Adds additional info for each RF link (tx/rx_rate, noise, signal)
* Removed redundant function.
Removed functions no longer needed.
Reworked getCurrentNeighbor function to add in the additional RF link info if requested.