* Support antenna selection and allow heading to be specified
* More antennas
* Heading -> Azimuth
* Ubiquiti's catalog
* Add Mikrotik builtin antennas
* Some Ubiquiti builtins
* JP Performance Antennas
* Added Altelix
* More Altelix
* More radios
* Add elevation
* Add generic omnis, sectors and dishes
* Improve selection
* Improve display for non-wireless devices
* Improve omni and builtin setup
* mode -> model typo in antennas.json
* Typos
* Fix bad gateway when saving
* Add antenna height above ground level.
Fix more bad gateways
* Update antennas.json
* More radio antennas
* More antennas
* Supernode option
* Change supernode 10/8 route injection.
Identify supernode in sysinfo.json
* Supernode tunnels use port 5526
* Advertise supernode-ness
* Update DNS if supernodes are available
* Open up supernodes DNS service to incoming mesh requests
* Simply nameserver update
* Support supernodes on hap ac2
* Improve supernode nameserver update reliability
* Rework how supernode nameservers are managed
* Improve supernode dns advertising
* Add super mesh button
* User supernode name not ip in advert
* Less intustive way to identify supernode dns
* Add supernode ignore options
Change supernode enabled -> enable
* Improve DNS updates
* Remove tunnels when switching to/from supernode mode
* Blackhole any unknown routes on the supernode to avoid recursing packets
* Add explicit reverse lookup rule for supernode when available
* Just use dnsmasq changes for both forward and reverse names
* Improve supernode detection
So it doesnt keep writing to flash
* Add reverse tunnel ip lookup to supernode
* enabled => enable
* Supernode tunnels start 172.30
* Remove supernode switch
* Simplify supernode check
* Fix nav test
* Link Quality Management experiment (built in)
* Protect LQM pages
* Omit "empty" mac addresses
* Integrate LQM v0.2
Includes proposed UI if this were built-in.
When LQM is enabled (advanced settings) the usual distance inputs are
replaced with "min snr' and "max distance" inputs which are the major
ones you might tweak, as well as a link to the LQM status page.
Other controls are now available (so protected) in advanced settings.
* Improve LQM updating
* Use running snr averages
* Merge app changes
* AREDN-ize the UI
* Improve status language
* Improved DtD detection
* Improve quality reporting
* Link Quality category
* Enable by default
* Better intergration
* Link => Neighbor
* Formatting
* Make sure initial page is populated without extra fetch
* Handle empty lqm.info
* Update with latest experiment algorithm changes
* Validate LQM settings before applying them
* Algorithm updates
* Improve quality reporting
* %% -> %
* Default max distance now 50 miles
* Get actual noise if radio will provide it
* low_snr => min_snr
* Dont print node description if we dont have one
* Remove properties duplicated from setup page
* Localize max distance. Miles in GB and US, Kilometers everywhere else.
* Ping link quality testing
* UDP 'ping' for quality check
* Change Active Settings title
* Expand ping test
* Improve messaging
* Add a ping penalty for neighbors which cannot be contacted in a timely manner.
* Remove user_blocks config option. No one needs to use this anymore.
* Localize distances on lqm page
* Improve status reporting
* First run emergency node setup.
When a node first runs LQM, if the default settings fail to connect to
a node we will now adjust them so that at least one node is viable.
* Restore blocking of mac addresses
* LQM now off by default
fixed#47
* sysinfo.json additions
lua library additions
Dependent on #389 and #391
Replaces #387
* additional check for nil needed
tested on a node with several very marginal RF links (IP, no host name) and it is working, so far.
also removed the decimal point on the n/lq values, we didn't need 10 places of accuracy. :)
* a couple more small changes
* changed neighborLinkInfo() function in aredn.info to show *all* links, not just RF.
Adds additional info for each RF link (tx/rx_rate, noise, signal)
* Removed redundant function.
Removed functions no longer needed.
Reworked getCurrentNeighbor function to add in the additional RF link info if requested.
Add support for the hAP lite model rb952UI-5ac2nD equivilent to
the UBNT AirRouter. The 5Ghz interface will be configured in a
2nd phase. This hAP lite model has double the RAM and Flash
of the AR. the 2Ghz is MIMO (5Ghz is single antenna).
* aredn: Node Description Enhancements
Node Description entry on setup page is now multiline.
Fixes#91
Node Description display on status page is now a table cell,
allowing for background color addition and word-wrapping.
Fixes#90
Description background color added to CSS files with colors appropriate to each theme.
Other CSS additions for the description input field on the setup page.
Updated onboard help file about the node description field (and fixed a typo)
* move some of the character filtering "higher up the chain" in perl.
javascript still will replace any new lines with a space in case the user hit's enter in the description entry box.
tested with curl and I can't find any problems yet.
* removed some commented lines that were not needed
* actually fix the typo I saw in help.html file.
* Added the Nodes locally hosted service listing to sysinfo.json
Added the Nodes locally hosted service listing to sysinfo.json file.
* Forgot to change api_version
* Change info[] section to be services_local to keep in line with the function is called
was info[local_services] now info[services_local]
* Added Uptime and Load Averages to the sysinfo.json file.
All code copied from Darryl, dman776.
* Updated Api Version number to 1.2.
Updated Api Version Number to 1.2.
Merging in latest release-3.15.1.0 changes into develop to provide a foundation with recent release fixes for the develop branch.
This should be 3.15.1.0b03 code.
Conflicts:
files/etc/crontabs/root
files/usr/local/bin/wscan
files/www/cgi-bin/sysinfo.json
Tim Wilkinson