Specifications:
* SoC: Qualcomm Atheros AR9344 (560 MHz)
* RAM: 64MB
* Storage: 8 MB
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
TP-Link CPE610-v2 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
Based on the same underlying hardware as the TP-Link CPE510
Power, LAN0, WLAN green LEDs
23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector
Flashing instructions:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron apcameron@softhome.net
* enhancement: added contact info/comment field for each tunnel connection.
Allows for a short comment or an email address so you can remember who to contact for each tunnel.
The field is optional and does not need to be filled out to get a tunnel connection up.
Also cleaned up some of the layout on the tunnel pages and hopefully made it a bit easier to tell what is what.
Fixes#457
* added `maxlength='50'` to the comment/contact field.
50 characters should be enough for an email address or a short comment.
* Allow for spaces in the Tunnel contact/comment field
This adds support for a popular low-cost 5GHz N based AP
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
Mesh status will show service entries of a remote mesh
node at the top with 0 ETX value. The owning mesh hostname
displays blank across the mesh network.
The root cause is OLSR not propagating the node's hostname due
to the admin assigning a conflicting/duplicate hostname. These
services will no longer show in mesh status.
* Add experimental support for the GL.iNet GL-AR150 - https://openwrt.org/toh/gl.inet/gl-ar150
Mesh networking and tunneling have been confirmed working.
This device has been confirmed capable of operating on channel -1, but /etc/config/wireless has to be manually edited to select this channel.
* www/cgi-bin/perlfunc.pm patched to add UI support for the GL.iNet GL-AR150
* www/cgi-bin/perlfunc.pm patched to add UI support for the GL.iNet GL-AR150 - seems like only 18 dBm TX power is possible
* Remove Experimental comments and designate as stable
* Configure Ethernet ports & VLANs for GL-AR150, and update README.md
* Fix misunderstanding re README.md
* Patch Upstream OpenWRT GL-AR150 LAN & WAN LED mapping, configure WLAN LED as mesh linked indicator.
* sysinfo.json additions
lua library additions
Dependent on #389 and #391
Replaces #387
* additional check for nil needed
tested on a node with several very marginal RF links (IP, no host name) and it is working, so far.
also removed the decimal point on the n/lq values, we didn't need 10 places of accuracy. :)
* a couple more small changes
* changed neighborLinkInfo() function in aredn.info to show *all* links, not just RF.
Adds additional info for each RF link (tx/rx_rate, noise, signal)
* Removed redundant function.
Removed functions no longer needed.
Reworked getCurrentNeighbor function to add in the additional RF link info if requested.
10MHz channel width is most commonly used. This default
will minimize how many new users are unable to connect
to a local mesh on first try. In 2GHz use ch -2
as only clear part 97 10MHz channel available and
predominently used.
* wscan can output results as json
* added a page for displaying scan results as json
* updated file permissions with +x
* added endpoint for wifi scan
* Revert "updated file permissions with +x"
This reverts commit 6f0a038334fbacc3f585f0a86fb7d9986a47b7d2.
* Revert "added a page for displaying scan results as json"
This reverts commit 4806ad01b6b717e2e02f248309a0257bb390af23.
* Revert "wscan can output results as json"
This reverts commit 75454e7e790a0457a0846182b0a8a44205772368.
* removed hardcoded device name
* exposed freqlist through the api
* moved signal.json code into the api
* old signal page uses /api?page=chart
* removed signal.json
* chart has targets for realtime and archive
* updated old signal page to use new api
* wscan can output results as json
* added a page for displaying scan results as json
* updated file permissions with +x
* added endpoint for wifi scan
* Revert "updated file permissions with +x"
This reverts commit 6f0a038334fbacc3f585f0a86fb7d9986a47b7d2.
* Revert "added a page for displaying scan results as json"
This reverts commit 4806ad01b6b717e2e02f248309a0257bb390af23.
* Revert "wscan can output results as json"
This reverts commit 75454e7e790a0457a0846182b0a8a44205772368.
* removed hardcoded device name
* exposed freqlist through the api
This reverts commit d5be7814b3.
Auto Distance is not ready for a release and will be
reintroduced afterwards. Added logic to reset '0' distance
to 60km so tower nodes will continue to respond after
upgrade if running the experimental auto distance
Add option for hap ac lite to select which band to
use for LAN AP option, 2GHz or 5GHz. Also, ensure
all wireless cards are defined when disabled to
prevent default wireless config options.
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
enable passwords with virtually any character, enable SSIDs
with virtually any character. ensure ap is always
encrypted to give operator control of client access and
license compliance. Remove (week) WEP encryption option.
* aredn: hAP ac lite enable 5GHz LAN Access Point
enable ability to bridge LAN physical ports with wireless
LAN Access Point capability. On dual band hAP ac lite,
used in parallel with mesh RF on 2GHz. Enables future
features on single band devices to turn off mesh RF and
repurposed for mesh LAN Access Point.
closes: #215
Also removed the description block from the mesh page if the description has not been set.
(there was a small grey area before, even with no description set)
* bugfix: Check for existing hostnames on the network in DHCP reservations
fixes#216
*additional check for existing hostname when creating new DHCP lease.
checks hosts_olsr file if entered hostname already exists or not on the connected network(s).
outputs info saying such and gives advice to prefix hostname with callsign.
* change to use =~ /\s$host\S/i
* Reworded warning message
* moved the position of the hostname check to only when you click "add" on the DHCP leases page.
this stops it checking all the previously entered hostnames.
* initial commit
* feature: advanced configuration page
fixes#230
* add help page updates
* added menu links to perlfunc.pm
* add default value for serverpath
* move "Reset to Firstboot" button from setup page to advancedconfig page
* secure page
minor ui changes
* center the help icon
* implement callback capabilities pre/post
* hardening uci calls to prevent command injection attacks
* moved settings to custom aredn uci file
* resolve shellcheck warnings
* feature: Provide firmware file advice for uploading firmware files
also reduces page size by removing unnecessary style info on option tags.
fixes#206
* update for Mikrotik filename exceptions
* correct download .list file name
* add support for cpe devices
Add support for the hAP lite model rb952UI-5ac2nD equivilent to
the UBNT AirRouter. The 5Ghz interface will be configured in a
2nd phase. This hAP lite model has double the RAM and Flash
of the AR. the 2Ghz is MIMO (5Ghz is single antenna).
* aredn: node description on mesh page, lat/lon on both status and mesh, olsr entries
Added node description to mesh status page
Fixes#161
Added Lat/Lon (if available) to status and mesh pages.
It is diplayed above the description and under the node name.
Fixes#145
Added OLSR Routing tables entries to status page just under the memory area
Also added this same info just above the buttons on the mesh status page
Fixes#160
* aredn: OLSR routing table entries
Small addition to the displayed info
* aredn: corrections
move lat lon if statement farther up
changed system command lines to have () around them...
* aredn: added comments for new lines
* aredn: more corrections
back to using backticks on system commands per short discussion with ae6xe
* aredn: updated some lines so they will not toss warnings in the syntax tests
* aredn: Node Description Enhancements
Node Description entry on setup page is now multiline.
Fixes#91
Node Description display on status page is now a table cell,
allowing for background color addition and word-wrapping.
Fixes#90
Description background color added to CSS files with colors appropriate to each theme.
Other CSS additions for the description input field on the setup page.
Updated onboard help file about the node description field (and fixed a typo)
* move some of the character filtering "higher up the chain" in perl.
javascript still will replace any new lines with a space in case the user hit's enter in the description entry box.
tested with curl and I can't find any problems yet.
* removed some commented lines that were not needed
* actually fix the typo I saw in help.html file.
with low memory conditions, typically on 32Mb RAM, the
device would become unresponsive in hours to days. The
symptoms only occured when no RF links. iw processes
would hang in Zombie state. Updates to use iwinfo where
possible and avoid using both iw and iwinfo. crontab
script is implemented to detect Zombie processes and free
up resources in the reduced chance the symptoms are still
occuring.
* config change to make uhttpd listen on port 80 and 8080
* add port 80 to tunnel firewall rules
* add port 80 to tunnel firewall rules in config, update help
* firewall rules for wan + dtdlink
I found a duplicated file in www, only 16k, but every bit matters now.
Removed the duplicate and the replaced the file with a minified version.
Updated www/cgi-bin/scan to use new minified file.
Tested. works fine.
This Device is almost the same as the CPE210 V2.0
Once Support for the TP-LINK CPE210 V3.0 gets added to the OpenWrt code we
will need to drop the patch 001-add_support_for_TP-Link_CPE210_v3.patch
Closes#32
* feature: add node description to status page
* feature: add node description to status page
* scrub for html like tags and correct node description label
* cleanup extra whitespace, comments, and debug stmt
* Added the Nodes locally hosted service listing to sysinfo.json
Added the Nodes locally hosted service listing to sysinfo.json file.
* Forgot to change api_version
* Change info[] section to be services_local to keep in line with the function is called
was info[local_services] now info[services_local]
* Added Uptime and Load Averages to the sysinfo.json file.
All code copied from Darryl, dman776.
* Updated Api Version number to 1.2.
Updated Api Version Number to 1.2.
Once the PR for this is accepted by Openwrt we will need to remove the file
001-add_support_for_TP-Link_CPE510_v2.patch
Removed 001-add_support_for_TP-Link_CPE210_v2.patch as PR #937 has been committed
Updated 99_setup_aredn_include to remove unused Rssi Led configuration
apcameron