Allows for the node admin to choose to have DHCP leased hostnames/IP's propagated over the rest of the mesh network or not.
Defaults to allowing the hostname/IP to propagate.
The hostname/IP will *still* be resolvable from the localnode and will show up in the list of hosts on the localnode only.
This allows for selected local mesh devices to be not available over the rest of the mesh network.
ie: switches, routers, cameras, etc.
This will work immediately for *new* DHCP leases when the checkbox is selected.
For *existing* DHCP leases, it may take a while for the network to update, if ever.
To speed up the process of full network OLSR "DNS" updating, reboot all the nearest neighbor device(s) to the node you made these changes to.
That seems to get the changes "out" to the rest of the network faster than normal.
Fixes#508
Change the Advanced Configuration warning banner: slightly wider to
distinguish from Alerts banner, add WARNING and make text color pure
white for contrast.
In the US, part 97 ham radio lower band edge is 5650.
Channel 131 @ 10MHz channel width is the lowest channel
setting that stays within allocation.
fixes#550
in the past nodes could be configured uniquely for
a given mode: ap, wifi client, mesh. Current behavior
in basic setup no longer has unique modes, rather wireless
cards can be configured in different modes in basic setup
and devices with multiple wireless interfaces can
be setup to use multiple modes at the same time.
fixes#533fixes#535
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
catch the tunnel comment field in perlfunc's read_post_data function where certain characters are changed to the html character entity in order to not interfere with the config files.
Tested with all kinds of crazy charcters such as: zdsfkh? <!@#$%^&*()> "quote"
Fixes#515
Specifications:
* SoC: Qualcomm Atheros AR9344 (560 MHz)
* RAM: 64MB
* Storage: 8 MB
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
TP-Link CPE610-v2 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
Based on the same underlying hardware as the TP-Link CPE510
Power, LAN0, WLAN green LEDs
23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector
Flashing instructions:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron apcameron@softhome.net
* enhancement: added contact info/comment field for each tunnel connection.
Allows for a short comment or an email address so you can remember who to contact for each tunnel.
The field is optional and does not need to be filled out to get a tunnel connection up.
Also cleaned up some of the layout on the tunnel pages and hopefully made it a bit easier to tell what is what.
Fixes#457
* added `maxlength='50'` to the comment/contact field.
50 characters should be enough for an email address or a short comment.
* Allow for spaces in the Tunnel contact/comment field
This adds support for a popular low-cost 5GHz N based AP
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
Mesh status will show service entries of a remote mesh
node at the top with 0 ETX value. The owning mesh hostname
displays blank across the mesh network.
The root cause is OLSR not propagating the node's hostname due
to the admin assigning a conflicting/duplicate hostname. These
services will no longer show in mesh status.
Eric