Add option for hap ac lite to select which band to
use for LAN AP option, 2GHz or 5GHz. Also, ensure
all wireless cards are defined when disabled to
prevent default wireless config options.
* aredn: hAP ac lite enable 5GHz LAN Access Point
enable ability to bridge LAN physical ports with wireless
LAN Access Point capability. On dual band hAP ac lite,
used in parallel with mesh RF on 2GHz. Enables future
features on single band devices to turn off mesh RF and
repurposed for mesh LAN Access Point.
closes: #215
* initial commit
* feature: advanced configuration page
fixes#230
* add help page updates
* added menu links to perlfunc.pm
* add default value for serverpath
* move "Reset to Firstboot" button from setup page to advancedconfig page
* secure page
minor ui changes
* center the help icon
* implement callback capabilities pre/post
* hardening uci calls to prevent command injection attacks
* moved settings to custom aredn uci file
* resolve shellcheck warnings
Add support for the hAP lite model rb952UI-5ac2nD equivilent to
the UBNT AirRouter. The 5Ghz interface will be configured in a
2nd phase. This hAP lite model has double the RAM and Flash
of the AR. the 2Ghz is MIMO (5Ghz is single antenna).
* config change to make uhttpd listen on port 80 and 8080
* add port 80 to tunnel firewall rules
* add port 80 to tunnel firewall rules in config, update help
* firewall rules for wan + dtdlink
olsrd-watchdog can trigger when the olsrd service is restarted
Such as when a tunnel comes up, or when a config change is
made to olsrd.
procd already monitors olsrd and makes sure it remains running.
With procd we no longer need olsrd-watchdog and can remove it.
fixes AREDN->ticket:215
Change-Id: I5067d380a22bd0ab5e597746478ef3e1ba05d72d
After OTA upgrade the timezone was kept in the system file
but not in the UI so when a user would save the timezone
would be overwritten.
fixes AREDN->ticket:186
Change-Id: I593afab0c3f67ba9d300228e9cbb47d7e3d894d1
RFC requires that the DHCP server include the default gateway (0.0.0.0/0) route as part the Classless network list.
Moved to node-setup so it can be set dynamically at setup run time.
fixes AREDN->ticket:155
This changes the beacon rate from once every 100tu's to once every 500tu's
1tu=1024 microseconds
This will decrease the amount of RF time being used by beacon packets.
This is especially important on 900MHz and 2.4GHz using 5MHz wide channels where 10 nodes beaconing 10x a second at ~256kbit/s can use up around 45% of the RF channel in beacons alone.
Other bands and channels and widths are not expected to see as significant an advantage due to the faster data rates.
This adds support for 802.11n data rates on the mesh.
This should improve dataspeeds across the board
MIMO devices like Rocket and NanoStation should be able to use dual chains which allows diverse data transmission on each chain increasing throughput
MCS data rates in theory should cut through noise better than legacy modulation and have higher speeds on each step which should allow overall higher datarate between nodes.
Config file is present upon initial start and in mesh mode.
Daemon still starts up in other modes but will not function w/o settings.
Firewall:
Permit access for UDP:161 (SNMPD) on WIFI and DTDLINK
Lan is permitted by default allow rules.
Makes the nodes advertise using DHCP Options 121 and 249 routes to the mesh (10.0.0.0/8) and the reserved (172.16.0.0/12) address ranges.
This change allows directing systems to prefer the mesh node for mesh ranges unless another network rule is more specific (such as a directly connected network)
This is mostly useful where a PC may have multiple network connections active as it improves the desire for the packets to travel via the mesh network.
Currently the:
10.0.0.0/8 range is used by mesh nodes and dtdlinking of mesh nodes.
172.27.0.0/16 is used for default LAN network on NAT nodes.
172.33.0.0/16 is for ad-hoc tunnels
All others in the advertised range are reserved for future network use.
Under Barrier Breaker sometimes OLSRD gets started before any interface is up causing OLSRD to shutdown because no interfaces exist.
Forces OLSRD to stay on and wait for the interfaces to come online.
Nodes sometimes show up as a mid1 entry when dtdlink and RF connected.
Sometimes the nodes will get the eth0 ip because wlan0 is not up yet.
Under Barrier Breaker the MainIP option is now supported as part of the uci system which allows us to restore using this setting.
We can now force the IP address that is claimed (wlan0) for the primary IP of the node.
Since a large number of the BBHNDev team has decided to create firmware fully independent of the BBHN Project the decision has been made to rebrand the firmware to differentiate from the origional BBHN work.
We would like to thank all those whom have worked on the BBHN firmware over the years and all those who continue to work on the firmware under AREDN(TM).
Joe Ayers