Makes the nodes advertise using DHCP Options 121 and 249 routes to the mesh (10.0.0.0/8) and the reserved (172.16.0.0/12) address ranges.
This change allows directing systems to prefer the mesh node for mesh ranges unless another network rule is more specific (such as a directly connected network)
This is mostly useful where a PC may have multiple network connections active as it improves the desire for the packets to travel via the mesh network.
Currently the:
10.0.0.0/8 range is used by mesh nodes and dtdlinking of mesh nodes.
172.27.0.0/16 is used for default LAN network on NAT nodes.
172.33.0.0/16 is for ad-hoc tunnels
All others in the advertised range are reserved for future network use.
Under Barrier Breaker sometimes OLSRD gets started before any interface is up causing OLSRD to shutdown because no interfaces exist.
Forces OLSRD to stay on and wait for the interfaces to come online.
Nodes sometimes show up as a mid1 entry when dtdlink and RF connected.
Sometimes the nodes will get the eth0 ip because wlan0 is not up yet.
Under Barrier Breaker the MainIP option is now supported as part of the uci system which allows us to restore using this setting.
We can now force the IP address that is claimed (wlan0) for the primary IP of the node.
Since a large number of the BBHNDev team has decided to create firmware fully independent of the BBHN Project the decision has been made to rebrand the firmware to differentiate from the origional BBHN work.
We would like to thank all those whom have worked on the BBHN firmware over the years and all those who continue to work on the firmware under AREDN(TM).
When a non mesh-gw node has a route via the WAN interface and through a mesh-gw it will choose the mesh-gw instead of the local WAN connection.and
We change the routing list to prefer the WAN link.
When the WAN is static configured the user will need to disable the WAN interface for the mesh internet to be chosen.
When the WAN is configured to dynamic the loss of a DHCP lease will allow the node to chose the remote mesh internet.
The simple solution would be to change the WAN to disabled and reboot to ensure a remote node is used instead if the local internet fails.
Thanks to Joe AE6XE and Clint AE5CA for pointing out this scenario.
By checking the "Keep Settings" box the node will run sysupgrade instead of mtd. Core settings are stored between installs and the _setup files are updated by pulling in missing items from the _setup.default files.
Using a press of around 5 seconds (3-7) the node will reset the passord to BBHN default and enable dhcp on the lan interface.
A press of around 10 seconds (8-12) will cause the node to reset the node to 'just flashed' status and cause the node to reboot.
Due to multiple issues that olsrd secure seems to make occur more often (but is not soley caused by OLSR Secure) causing olsr to crash olsr secure is being pulled while we work on the module.
This partialy reverts commit 553c126490.
tag: RequiresProtocolIncrement
Required for 900mhz devices to be supported due to band size.
This can also be useful for allowing more devices to fit into the same amount of RF space as nodes may often not need full 20mhz wide channels.
2.4ghz while using standard BBHN SSID is restricted to 20mhz for compatibility.
ref BBHN->ticket:50
SSID Version increment for
changeset:a4dd9a9bdd798b05d76d71d135d860f57cb83d8d/bbhn_ar71xx and changeset:553c126490790a3d9873741551813a635a439c0b/bbhn_ar71xx
ref BBHN->ticket:28 and BBHN->ticket:37
Due to the 10.x network no longer going out via wifi we now have a dedicated daemon for performing node identification out the wifi interface. The old fccid scripts are no longer used.
ref BBHN->ticket:28
NOTE: This patch requires a kernel upgrade to fully work.
Adds new value wifi_country.
Country HX is being chosen for HAM band use.
Country selection is needed to help the device stay withing regulatory domain for worldwide use.
ref BBHN->ticket:29
The dtdlink interface is vlan 2 on eth0 and is used for linking two or more devices together.
This will allow for band-to-band repeaters, sector antenna setups, etc.
see BBHN->ticket:28
Includes band/channel mapping
Code to set default RF channel on first boot
Add many 5ghz Ubiquiti devices in a testing phase including:
NanoBeam M5 (Intl), NanoBridge M5, AirGrid M5 HP, AirGrid M5, NanoStation M5, NanoStation Loco M5, Bullet M5, Rocket M5
see BBHN->ticket:29
In order to maintain compatibility with existing deployed nodes, known common encrypted ports will NOT be blocked by default.
Users will receive a message during first setup encouraging them to review the rules that apply to how they intend to use their node and that laws very by country and frequency.
A package blockknownencrypted has been created in changeset:123a521df2b63ba1c5bdd6ad94ac402b86394579/bbhn_packages to be used in blocking known encrypted ports if the user feels it is necessary.
As developers we are not stating an opinion as to what the rules say or do not say in relationship to the traffic this deals with. Each user will need to make their own determination of the rules.
This has been the current case since day one.
New file fwinfo page shows if the package is installed AND displays the active firewall rules at the time of the access. This allows future grown to help test (because of the adhoc nature of the mesh) if packet filtering is the cause of a connection not working.
see BBHN->ticket:3
files/etc/hosts was deleted in b948d97/bbhn_ar71xx
Recovered and modified IP address for localnode.
dnsmasq needs /etc/hosts to be pre-populated with "localnode"
otherwise users have to type the ip address for first log in.
We populate this file via node-setup on mode changes.
fixes BBHN->ticket:10
Includes removing files that are provided by packages instead
of being embedded as binaries.
Changes made for UBNT hardware AND for newer base openwrt (Backfire)
Darryl Quinn