Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Specifications:
* SoC: Qualcomm Atheros AR9344 (560 MHz)
* RAM: 64MB
* Storage: 8 MB
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
TP-Link CPE610-v2 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
Based on the same underlying hardware as the TP-Link CPE510
Power, LAN0, WLAN green LEDs
23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector
Flashing instructions:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron apcameron@softhome.net
remove ZRAM option causing boot errors and not used
remove unused olsr secure plugin from image to save space
add option to build blockknownencrytion aredn package
This adds support for a popular low-cost 5GHz N based AP
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* Add experimental support for the GL.iNet GL-AR150 - https://openwrt.org/toh/gl.inet/gl-ar150
Mesh networking and tunneling have been confirmed working.
This device has been confirmed capable of operating on channel -1, but /etc/config/wireless has to be manually edited to select this channel.
* www/cgi-bin/perlfunc.pm patched to add UI support for the GL.iNet GL-AR150
* www/cgi-bin/perlfunc.pm patched to add UI support for the GL.iNet GL-AR150 - seems like only 18 dBm TX power is possible
* Remove Experimental comments and designate as stable
* Configure Ethernet ports & VLANs for GL-AR150, and update README.md
* Fix misunderstanding re README.md
* Patch Upstream OpenWRT GL-AR150 LAN & WAN LED mapping, configure WLAN LED as mesh linked indicator.
This reverts commit d5be7814b3.
Auto Distance is not ready for a release and will be
reintroduced afterwards. Added logic to reset '0' distance
to 60km so tower nodes will continue to respond after
upgrade if running the experimental auto distance
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Add kernel build options to conserve RAM. Measured 520k reduction.
disable CRASHLOG interface, we can't really see it anyway
CONFIG_KERNEL_CRASHLOG=n
remove process core dump support (see above reasoning)
CONFIG_KERNEL_ELF_CORE=n
there is no "swap"
CONFIG_KERNEL_SWAP=n
remove debug symbols
CONFIG_KERNEL_KALLSYMS=n
remove debug info
CONFIG_KERNEL_DEBUG_INFO=n
more unnecessary kernel exports
CONFIG_STRIP_KERNEL_EXPORTS=y
remove libraries of unnecessary functions
CONFIG_USE_MKLIBS=y
compress /tmp
CONFIG_PROCD_ZRAM_TMPFS=y
seldom used key stroke
CONFIG_KERNEL_MAGIC_SYSRQ=n
Not used with AREDN
CONFIG_PACKAGE_MAC80211_MESH=n
Above options Ref: https://openwrt.org/docs/guide-user/additional-software/saving-space#modifying_build_configuration_variables
-------------
Additional options
CONFIG_BUSYBOX_DEFAULT_MKSWAP=n
CONFIG_BUSYBOX_CONFIG_MKSWAP=n
improved "top" command.
CONFIG_BUSYBOX_CONFIG_FEATURE_TOP_INTERACTIVE=y
additional modules to build
CONFIG_PACKAGE_kmod-usb3=m
CONFIG_PACKAGE_block-mount=m
CONFIG_PACKAGE_kmod-usb-storage=m
CONFIG_PACKAGE_kmod-usb-storage-extras=m
CONFIG_PACKAGE_kmod-usb-storage-uas=m
Additional filesystem modules complementing USB storage
CONFIG_PACKAGE_kmod-fs-vfat=m
CONFIG_PACKAGE_kmod-fs-ntfs=m
CONFIG_PACKAGE_kmod-fs-ext4=m
CONFIG_PACKAGE_e2fsprogs=m
Reduce log usage of /tmp and RAM
I can't find my notes of course...
CONFIG_LOG_BUF_SHIFT=16
CONFIG_LOG_CPU_MAX_BUF_SHIFT=16
additional options to support performance metrics
CONFIG_BUSYBOX_CONFIG_IOSTAT=y
CONFIG_BUSYBOX_CONFIG_RENICE=y
CONFIG_BUSYBOX_CONFIG_FEATURE_PS_LONG=y
Add support for the hAP lite model rb952UI-5ac2nD equivilent to
the UBNT AirRouter. The 5Ghz interface will be configured in a
2nd phase. This hAP lite model has double the RAM and Flash
of the AR. the 2Ghz is MIMO (5Ghz is single antenna).
Closes#81
* Trim Packages
Kernel support for USB has been moved to modules
libpcap and tcpdump have been moved to modules
libnetsnmp and snmpd have been moved to modules
IPv6 has been removed from the kernel
IPv6 support has been removed from busybox network utils as well.
(no more funny DNS responses in nslookup!)
* Remove ping6 and traceroute6
They are no longer needed
* Changed patch name and number and updated series file
AbortRetryFail