* Initial OpenWRT 23.05.0 merge
* Fix get_rfchannels for new iwinfo format
* Fix initial wlan name
* Move patches to 5.15 from 5.10
* Fix flash write problem on Ubiquiti devices
* Use new ssl patch
* Reduce binary sizes
* Have to have hostapd installed now, even on tiny builds
* Simplify device support
* Revert Mikrotik NAND sysupgrade system.
OpenWRT doesnt really support Mikrotik NAND devices after 2019 and the
new support appeared broken. So reverted to the 2022 mechanism which does
work and avoid upgrade problems.
* Fixes for tiny builds
* More tiny shrinking
* Fix newly added firewall rules
* Update permanent packages
* Update permanent packages
* Support for Nanobeam 2AC (2.4GHz) device. 20MHz channels only.
* Update support
* Add GL.iNet B1300
* Add to radios.json
* Update supported devices
* Dont force the LAN DHCP to run
* Revert CURL SSL test
* Fix radio count when there are no radios
* Switch the lan ports on the gl-b1300
* Add support for GL.iNET Beryl MT1300
* Fix visual lat/lon setting bug
* Make the setup "Save Changes" button also save the location data
* Fix location/map system with geo location fallback
* Recolor
* Fix default bandwidth selection
* Support multi-band radios
* Generic mechanism to set compat version to 1.1
* Switch ethernet ports
* 20 MHz channels only
* Update docs
* Add ham channels to Mediatek chips (20MHz only)
* Automatically update the permpkg list when we upgrade
* Fix 10MHz mode for Ubiquiti AC devices
* Fix tiny builds
* Bump the watch timeout for restarting olsrd
olsrd is reliable these days, and very occasionally this
was restarting it unnecessarily
* Supernode option
* Change supernode 10/8 route injection.
Identify supernode in sysinfo.json
* Supernode tunnels use port 5526
* Advertise supernode-ness
* Update DNS if supernodes are available
* Open up supernodes DNS service to incoming mesh requests
* Simply nameserver update
* Support supernodes on hap ac2
* Improve supernode nameserver update reliability
* Rework how supernode nameservers are managed
* Improve supernode dns advertising
* Add super mesh button
* User supernode name not ip in advert
* Less intustive way to identify supernode dns
* Add supernode ignore options
Change supernode enabled -> enable
* Improve DNS updates
* Remove tunnels when switching to/from supernode mode
* Blackhole any unknown routes on the supernode to avoid recursing packets
* Add explicit reverse lookup rule for supernode when available
* Just use dnsmasq changes for both forward and reverse names
* Improve supernode detection
So it doesnt keep writing to flash
* Add reverse tunnel ip lookup to supernode
* enabled => enable
* Supernode tunnels start 172.30
* Remove supernode switch
* Simplify supernode check
* Fix nav test
* Make admin and user bar menus pluggable
* Realign header block to stop is moving around
* Remove ref
* Use modular nav to disable ineligable options during initial install
* Dont offer tunnel menus options when no tunnel daemon installed.
This is for low-memory devices
* Simplify
* Improve messaging when running ram image
* Disable rather than hide vpn menu items on tiny memory devices
* Move menu navs
* Enable RTS/CTS when we detect hidden nodes
* Only change rts setting when we need to
* RTS advanced config option
* Include neighbors blocked neighbors (they still transmit)
* Bump default RTS threashold
* Report list of hidden node rather than yes/no
* Canonical hostnames
* When we enable RTS, enable it for all traffic by default
* Show hidden neighbors in display
* Default RTS threshold to -1 (always off)
* Update to Openwrt 21.02 and add support for the CPE710 v1
Update scripts to change references to ifname to device due to a change in Openwrt naming
reverse-wpad-basic-wolfssl and disable SSL on Curl
NOTE: The compile host must have python3-distutils installed for gpsd to build
* aredn: initial working upgrade to openwrt 21.02.1
* aredn: update 1 to working upgrade to openwrt 21.02.1
* aredn: add cpe710v1 to build config
* Andrew's patches
* Remove duplicates + display perl
* Temp disable wifi extension patch
* ifname/ports support
* Add spectrum patch back in
* Generic function to extra interfaces
* New api to get wifi ifname
* Disables jails
* Style link
* aredn: partial upgrade to openwrt 22.0.3.0
added AC device images and partial migration to 22.0.3.0
firewall upgrade pending
* aredn: update mesh-release and revert config.mk
* Unused
* NFT firewall rewrite
* Common-isze configs
* Fix network layout for hap2
* Use local packages dev (new firewall rules)
* Add HAP2
* Add pause after network restart to let bridge reinitialize
* Various lua fixes for new lua version
* Tweak config
* Re-fix networking (lost patch change)
* Add new radio names
* Tolerate missing wifi
* Fix hap-lite switch setup
* More devices
* New radio id
* Build Rocket 5AC lite
* Remove need for luci.sys
* Remove need for luci.sys
* Explicitly name wlan interfaces
* Handle different compatibility verisoning
* Update networking for switches
* ipref version bump
* Extra flag for curl
* Better compat_version fix
* Remove wolfssl
* Fix dns server
* Fix device name
* Unused
* Remove things we dont need
* Remove unused packages
* Generic macaddr overrides
* Fix uci commit
* Fix luci.template.parser to avoid luci.http loading the real thing
* Rocket-M build
* Add search-domain dhcp option
* Turn of ipv6
* No IPV6 in dnsmasq
* Override mac addresses if devices all the same
* Working from master (for now)
* Put back hostap
* Disable old ethmac fixup
* Tweak configs
* Move back to v22.03.2
Leave ipq4019 builds to master
* Need IPV6 to compile nft firewall
* Rocket-M fixes
* Before we start
* WIP
* Working snapshot
* Cleaned patches
* Merged patch
* Single patch to support HAP2
* Fix typo
* Add nanostation-m
* 5/10Mhz patch
* 5+10MHz patch for ath10k-ct driver
* Extend 2Ghz channel check to include -4 to -1
* Add chanbw setup for ath10k (like ath9k)
* Added TP-Link CPE710 v1
* Override firmwares
* Missing patch
* Dropbear config like 3.22.8.0
* Add Ubiquiti Rocket 5AC Lite
* Fix c6
* Update
* Need more scan channels
* Remove IPV6
* Improve mac fixups
* Put back missing nft app
* IPv6 removed so dont have to disable it
* Fix rocket-m flash bug
* Fix nanostation-m
* Nanobridge is tiny
* Fix wifi order for ar750
* Rocket M5 XW support
* New rates
* Fix firewall4 so we don't need IPv6
* Allow channel width to be restricted
* Move channel list into library
* Fix naming
* Mechanism to block specific channels on specific radios
* Refresh buttons
* routerboard-sxt-5nd
* CPE605 v1.0
* Improve rocket m xw
* tpink
* Update patch
* Update to remove disable
* Remove BW restrictions on cpe710
* Restrict to what has been tested
* Remove test BW restrictions
* sxtsq-5-ac
* Update
* Update
* powerbeam-m5-300 support
* Fix
* Fix hap2
* Tidy unused patches
* Remove limit
* Add ubnt_bullet-m-ar7241
* Added ubnt_nanobeam-ac-gen2
* Fix typo
* Tolerate missing dtd ip
* Explicitly gix hap2 mac addresses
* Fix some broken patches
* Hap2 wont work at 5MHz
* Ubiquiti LiteBeam 5AC Gen2
* Fix compat_version for sxt 5ac
* Update patch
* Unused
* Fix lan configuration for some devices
* Rolling average of noise level
* Unused
* Split out the ath10k rssi monitor (its very simple at the moment)
* Ignore .DS_Store
* Reboot if ethernet doesnt come up (but only once!)
* reboot returns - add exit
* Add some logging info
* Fix ]
* Check all possibly ethernet bridges
* Improve mac fixing
* Remove HostAP on small memory devices
* Reduce dropbear footprint
* Add setsid
* Kill hostap when upgrading to save memory
* Different way to detect hostapd unavailable
* New build steps
* Improve manager logging
* Fix name conflict for the two monitors
* Try to improve test mesh name resolve problem
* Migrate tiny to generic (tiny doesnt work properly)
* Typo
* Another attempt to fix macs for Mikrotik
* Protect against missing trackers
* Fix wpad for ipq40xx
* Remove old tunnel check code
* Enable ZRAM swap to aid low memory devices
* ath10k noise can something be out of range - protect against that
* Updated with current devices and status
* Update firmware which has been tested
* Updated with more builds
* More binary/README
* Fix css error
* Start noise at sensible base level
* Unfix the css so it looks how it use to.
* Save as much memory as we can on lowmem nodes
* Hide some options on low memory devices
* Add "eol" to 32MB devices
* Restart network rather than reboot node if it seems to be broken
* Fixes
* Revert network reset
* Fix ar750 networking
* Continue to trim tiny configs
* More devices
* Dump IW output messages
* Fix Rocket 5AC intermittent ethernet issue
* Ethernet fix for PowerBeam 5AC 500
* More tiny size reduction
* More support data
* Fixed POE and USB power features
* Add Ubiquiti NanoBeam AC (gen1)
* NanoStation (not NanoBeam)
* Add mii-tool package
* Device updates
* Bump update time to 5 minutes
* Fix ethernet negotiation for rocker-5ac and nanobeam
* Fix iplookup
* Config changes based on call feedback
* Radio listing fixes
* Update with more untested builds
* Fallback TxMbps extracted from iw station dump
* Fix tunnel detection for low memory nodes
* Remove unused feed packages
* snapshot build
* Update stability info
* Add powerbeam-5ac-500
* Typo
* Add missing 3.22.1.0
* Add MikroTik LHG 5 AC
* Fix permissions
* Fix permissions
* AirGrid's take Bullet builds
* Mikrotik AC3
* Improve supportdata structure a little to make it easier to find things
* Restore WAN VLAN overrides
* Fix vlan regex for hap2 and hap3
* Support old and new style poe controls
* hap-ac3 is version 1.1
* Handle typo in some openwrt config files
* Fix HAP AC3 install
* Update hap ac3 status
* Support user overrides for network ports (non-swconfig devices)
* LHG 5AC support
* Remove -nand
* Remove non-working platform.sh change
* tunnel weight override
* Omit LinkQualityMult when value is 1
* Add mANTBox 19s and 15s
* Support ath79 mikrotik devices which require ath10k in the initramfs
Co-authored-by: apcameron <apcameron@softhome.net>
Co-authored-by: Joe AE6XE <ae6xe@arrl.net>
Co-authored-by: Joe Ayers <joe@arrl.net>
* Link Quality Management experiment (built in)
* Protect LQM pages
* Omit "empty" mac addresses
* Integrate LQM v0.2
Includes proposed UI if this were built-in.
When LQM is enabled (advanced settings) the usual distance inputs are
replaced with "min snr' and "max distance" inputs which are the major
ones you might tweak, as well as a link to the LQM status page.
Other controls are now available (so protected) in advanced settings.
* Improve LQM updating
* Use running snr averages
* Merge app changes
* AREDN-ize the UI
* Improve status language
* Improved DtD detection
* Improve quality reporting
* Link Quality category
* Enable by default
* Better intergration
* Link => Neighbor
* Formatting
* Make sure initial page is populated without extra fetch
* Handle empty lqm.info
* Update with latest experiment algorithm changes
* Validate LQM settings before applying them
* Algorithm updates
* Improve quality reporting
* %% -> %
* Default max distance now 50 miles
* Get actual noise if radio will provide it
* low_snr => min_snr
* Dont print node description if we dont have one
* Remove properties duplicated from setup page
* Localize max distance. Miles in GB and US, Kilometers everywhere else.
* Ping link quality testing
* UDP 'ping' for quality check
* Change Active Settings title
* Expand ping test
* Improve messaging
* Add a ping penalty for neighbors which cannot be contacted in a timely manner.
* Remove user_blocks config option. No one needs to use this anymore.
* Localize distances on lqm page
* Improve status reporting
* First run emergency node setup.
When a node first runs LQM, if the default settings fail to connect to
a node we will now adjust them so that at least one node is viable.
* Restore blocking of mac addresses
* LQM now off by default
fixed#47
Tim Wilkinson