Add option for hap ac lite to select which band to
use for LAN AP option, 2GHz or 5GHz. Also, ensure
all wireless cards are defined when disabled to
prevent default wireless config options.
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
enable passwords with virtually any character, enable SSIDs
with virtually any character. ensure ap is always
encrypted to give operator control of client access and
license compliance. Remove (week) WEP encryption option.
* aredn: hAP ac lite enable 5GHz LAN Access Point
enable ability to bridge LAN physical ports with wireless
LAN Access Point capability. On dual band hAP ac lite,
used in parallel with mesh RF on 2GHz. Enables future
features on single band devices to turn off mesh RF and
repurposed for mesh LAN Access Point.
closes: #215
Also removed the description block from the mesh page if the description has not been set.
(there was a small grey area before, even with no description set)
* bugfix: Check for existing hostnames on the network in DHCP reservations
fixes#216
*additional check for existing hostname when creating new DHCP lease.
checks hosts_olsr file if entered hostname already exists or not on the connected network(s).
outputs info saying such and gives advice to prefix hostname with callsign.
* change to use =~ /\s$host\S/i
* Reworded warning message
* moved the position of the hostname check to only when you click "add" on the DHCP leases page.
this stops it checking all the previously entered hostnames.
* initial commit
* feature: advanced configuration page
fixes#230
* add help page updates
* added menu links to perlfunc.pm
* add default value for serverpath
* move "Reset to Firstboot" button from setup page to advancedconfig page
* secure page
minor ui changes
* center the help icon
* implement callback capabilities pre/post
* hardening uci calls to prevent command injection attacks
* moved settings to custom aredn uci file
* resolve shellcheck warnings
* feature: Provide firmware file advice for uploading firmware files
also reduces page size by removing unnecessary style info on option tags.
fixes#206
* update for Mikrotik filename exceptions
* correct download .list file name
* add support for cpe devices
groups with custom rules created in /etc/local/mesh-firewall
for echolink, ampr.net, and other integrations with internet
based appications can preserve rules across a firmware
upgrade by locating the custom rules in this directory
using a file named 59-custom-rules
Add support for the hAP lite model rb952UI-5ac2nD equivilent to
the UBNT AirRouter. The 5Ghz interface will be configured in a
2nd phase. This hAP lite model has double the RAM and Flash
of the AR. the 2Ghz is MIMO (5Ghz is single antenna).
* aredn: node description on mesh page, lat/lon on both status and mesh, olsr entries
Added node description to mesh status page
Fixes#161
Added Lat/Lon (if available) to status and mesh pages.
It is diplayed above the description and under the node name.
Fixes#145
Added OLSR Routing tables entries to status page just under the memory area
Also added this same info just above the buttons on the mesh status page
Fixes#160
* aredn: OLSR routing table entries
Small addition to the displayed info
* aredn: corrections
move lat lon if statement farther up
changed system command lines to have () around them...
* aredn: added comments for new lines
* aredn: more corrections
back to using backticks on system commands per short discussion with ae6xe
* aredn: updated some lines so they will not toss warnings in the syntax tests
* aredn: Node Description Enhancements
Node Description entry on setup page is now multiline.
Fixes#91
Node Description display on status page is now a table cell,
allowing for background color addition and word-wrapping.
Fixes#90
Description background color added to CSS files with colors appropriate to each theme.
Other CSS additions for the description input field on the setup page.
Updated onboard help file about the node description field (and fixed a typo)
* move some of the character filtering "higher up the chain" in perl.
javascript still will replace any new lines with a space in case the user hit's enter in the description entry box.
tested with curl and I can't find any problems yet.
* removed some commented lines that were not needed
* actually fix the typo I saw in help.html file.
with low memory conditions, typically on 32Mb RAM, the
device would become unresponsive in hours to days. The
symptoms only occured when no RF links. iw processes
would hang in Zombie state. Updates to use iwinfo where
possible and avoid using both iw and iwinfo. crontab
script is implemented to detect Zombie processes and free
up resources in the reduced chance the symptoms are still
occuring.
* config change to make uhttpd listen on port 80 and 8080
* add port 80 to tunnel firewall rules
* add port 80 to tunnel firewall rules in config, update help
* firewall rules for wan + dtdlink
I found a duplicated file in www, only 16k, but every bit matters now.
Removed the duplicate and the replaced the file with a minified version.
Updated www/cgi-bin/scan to use new minified file.
Tested. works fine.
This Device is almost the same as the CPE210 V2.0
Once Support for the TP-LINK CPE210 V3.0 gets added to the OpenWrt code we
will need to drop the patch 001-add_support_for_TP-Link_CPE210_v3.patch
Closes#32
* feature: add node description to status page
* feature: add node description to status page
* scrub for html like tags and correct node description label
* cleanup extra whitespace, comments, and debug stmt
* Added the Nodes locally hosted service listing to sysinfo.json
Added the Nodes locally hosted service listing to sysinfo.json file.
* Forgot to change api_version
* Change info[] section to be services_local to keep in line with the function is called
was info[local_services] now info[services_local]
dman776