This adds support for a popular low-cost 5GHz N based AP
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* Add experimental support for the GL.iNet GL-AR150 - https://openwrt.org/toh/gl.inet/gl-ar150
Mesh networking and tunneling have been confirmed working.
This device has been confirmed capable of operating on channel -1, but /etc/config/wireless has to be manually edited to select this channel.
* www/cgi-bin/perlfunc.pm patched to add UI support for the GL.iNet GL-AR150
* www/cgi-bin/perlfunc.pm patched to add UI support for the GL.iNet GL-AR150 - seems like only 18 dBm TX power is possible
* Remove Experimental comments and designate as stable
* Configure Ethernet ports & VLANs for GL-AR150, and update README.md
* Fix misunderstanding re README.md
* Patch Upstream OpenWRT GL-AR150 LAN & WAN LED mapping, configure WLAN LED as mesh linked indicator.
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
* aredn: hAP ac lite enable 5GHz LAN Access Point
enable ability to bridge LAN physical ports with wireless
LAN Access Point capability. On dual band hAP ac lite,
used in parallel with mesh RF on 2GHz. Enables future
features on single band devices to turn off mesh RF and
repurposed for mesh LAN Access Point.
closes: #215
Config the NanoStation M2/M5 XW devices to be fully
functional with a standard aredn port definition.
The vlans are not configured in the switch, rather
acting like a dumb swtich, enabling tagged and untagged
packets to exist on the same switch port at the same time.
This commit enables the ports on the switch to directly
send all traffic to all other ports when not configured
directly in vlan mode.
add notes on how to build 3.16.2.0 older release
remove make instructions that no longer apply
update highlevel change log of github changes from prior tools
Add support for the hAP lite model rb952UI-5ac2nD equivilent to
the UBNT AirRouter. The 5Ghz interface will be configured in a
2nd phase. This hAP lite model has double the RAM and Flash
of the AR. the 2Ghz is MIMO (5Ghz is single antenna).
dman776