* Link Quality Management experiment (built in)
* Protect LQM pages
* Omit "empty" mac addresses
* Integrate LQM v0.2
Includes proposed UI if this were built-in.
When LQM is enabled (advanced settings) the usual distance inputs are
replaced with "min snr' and "max distance" inputs which are the major
ones you might tweak, as well as a link to the LQM status page.
Other controls are now available (so protected) in advanced settings.
* Improve LQM updating
* Use running snr averages
* Merge app changes
* AREDN-ize the UI
* Improve status language
* Improved DtD detection
* Improve quality reporting
* Link Quality category
* Enable by default
* Better intergration
* Link => Neighbor
* Formatting
* Make sure initial page is populated without extra fetch
* Handle empty lqm.info
* Update with latest experiment algorithm changes
* Validate LQM settings before applying them
* Algorithm updates
* Improve quality reporting
* %% -> %
* Default max distance now 50 miles
* Get actual noise if radio will provide it
* low_snr => min_snr
* Dont print node description if we dont have one
* Remove properties duplicated from setup page
* Localize max distance. Miles in GB and US, Kilometers everywhere else.
* Ping link quality testing
* UDP 'ping' for quality check
* Change Active Settings title
* Expand ping test
* Improve messaging
* Add a ping penalty for neighbors which cannot be contacted in a timely manner.
* Remove user_blocks config option. No one needs to use this anymore.
* Localize distances on lqm page
* Improve status reporting
* First run emergency node setup.
When a node first runs LQM, if the default settings fail to connect to
a node we will now adjust them so that at least one node is viable.
* Restore blocking of mac addresses
* LQM now off by default
fixed#47
* Migrate /etc/config/dmz-mode to /etc/dmz-mode
* Migrate dmz_mode into /etc/config/aredn
* Use cmd append
* Changes should be in /etc/config.mesh
* Add commit
* add uci migration script
* removed debug lines
* added newline to end
* include gridsquare values
* migrate lat/lon/gridsquare to uci format
* remove from sysupgrade kept files list
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Specifications:
* SoC: Qualcomm Atheros AR9344 (560 MHz)
* RAM: 64MB
* Storage: 8 MB
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
* aredn: hAP ac lite enable 5GHz LAN Access Point
enable ability to bridge LAN physical ports with wireless
LAN Access Point capability. On dual band hAP ac lite,
used in parallel with mesh RF on 2GHz. Enables future
features on single band devices to turn off mesh RF and
repurposed for mesh LAN Access Point.
closes: #215
Add support for the hAP lite model rb952UI-5ac2nD equivilent to
the UBNT AirRouter. The 5Ghz interface will be configured in a
2nd phase. This hAP lite model has double the RAM and Flash
of the AR. the 2Ghz is MIMO (5Ghz is single antenna).
Once the PR for this is accepted by Openwrt we will need to remove the file
001-add_support_for_TP-Link_CPE510_v2.patch
Removed 001-add_support_for_TP-Link_CPE210_v2.patch as PR #937 has been committed
Updated 99_setup_aredn_include to remove unused Rssi Led configuration
Move httpd.conf to not store password and instead depend on the shadow password file.
Also tag the 40_aredn_migrate-httpdconf script to be +x. Not strictly necessary but wish to have this standard
Change-Id: I018d9a3294e45af2316b3c3947ef2a7d8081268b
Not getting much debug information at moment, would like to put this in uci-defaults but with issues that I can't seem to log at moment (and not having serial cable for this device) I'm going with lets put it in /etc/init.d/local before nvram and similar gets set.
ref AREDN->ticket:115
Old code would set mac on the sub-vlan not the master interface which could cause issues.
Rework to be more functional in the future and to work correctly on vlan interfaces.
ref AREDN->ticket:115
wifi detect is called in /etc/init.d/boot before uci_apply_defaults is called.
Because of this if we don't have the data about the radio0path we need to remove the wifi config file first before calling wifi detect.
Needs to be in uci-defaults to be sure these data sets execute BEFORE the OS boots
We also need to get radio0 path because its mandatory for wifi to work.
Needed for sysupgrade from 3.0.2 to latest version.
Remove setting RF channel on first boot in uci-defaults.
This should allow the node to use standard wifi channels when it boots allowing mesh setup to be run from a laptop or mobile device.
We will later move them to a real mesh channel during the mesh setup page.
Should also resolv issue where nodes were booting up on channel -2 and similar and wifi would refuse to start due to regdomain.
Includes band/channel mapping
Code to set default RF channel on first boot
Add many 5ghz Ubiquiti devices in a testing phase including:
NanoBeam M5 (Intl), NanoBridge M5, AirGrid M5 HP, AirGrid M5, NanoStation M5, NanoStation Loco M5, Bullet M5, Rocket M5
see BBHN->ticket:29
Tim Wilkinson