0741cf61fc
bugfix: NanoBeam M5 XW hardware definition.
...
Adjust power levels to reflect what is in the board.info
This was likely a typo when I put the device in the first time.
In addition adjust naming to match Ubiquiti device rename.
{{{
board.sysid=0xe4e5
board.cpurevision=0x00001122
board.name=PowerBeam M5
board.shortname=P5B
board.subtype=400
board.netmodes=7
board.hwaddr=0418D65EEB39
board.reboot=40
board.upgrade=150
board.phycount=1
board.phy.1.maxmtu=2024
board.phy.2.maxmtu=2024
radio.1.name=
radio.1.shortname=
radio.1.bus=ahb
radio.1.subsystemid=0xe4e5
radio.1.subvendorid=0x0777
radio.1.txpower.max=26
radio.1.txpower.offset=4
radio.1.antennas=2
radio.1.def_antenna=1
radio.1.antenna.1.id=1
radio.1.antenna.1.name=400
radio.1.antenna.1.gain=25
radio.1.antenna.2.id=2
radio.1.antenna.2.name=Feed only
radio.1.antenna.2.gain=3
}}}
ref AREDN->ticket:185
Change-Id: I71d2a944b6abb9e30862d7ada7f46b80df2c731c
2016-09-24 08:37:02 -07:00
717b39c2fd
hardware: Add support to obtain boardid from more Ubiquiti devices.
...
Obtain the board ID from the EEPROM on *-m-xw devices.
ref AREDN->ticket:185
ref AREDN->ticket:43
Change-Id: I86247640773a1f6cbd3c4792502d7da4890a46a4
2016-09-24 08:28:31 -07:00
bb83809472
hardware: Testing support for CPE210 v1.1
...
Add board definition for CPE210 v1.1 in testing mode.
{{{
========== iw phy phy0 info ==========
Wiphy phy0
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 9 (up to 4050m)
Device supports AP-side u-APSD.
Device supports T-DLS.
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* WDS
* monitor
* mesh point
* P2P-client
* P2P-GO
* outside context of a BSS
Band 1:
Capabilities: 0x11ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-15
Frequencies:
* 2397 MHz [-2] (30.0 dBm) <-- This is kernel fallback when channel is
* 2402 MHz [-1] (30.0 dBm) <-- not defined in radio EEPROM, set to 22 instead
* 2412 MHz [1] (22.0 dBm)
* 2417 MHz [2] (23.0 dBm)
* 2422 MHz [3] (23.0 dBm)
* 2427 MHz [4] (23.0 dBm)
* 2432 MHz [5] (23.0 dBm)
* 2437 MHz [6] (23.0 dBm)
* 2442 MHz [7] (23.0 dBm)
* 2447 MHz [8] (23.0 dBm)
* 2452 MHz [9] (23.0 dBm)
* 2457 MHz [10] (23.0 dBm)
* 2462 MHz [11] (23.0 dBm)
* 2467 MHz [12] (30.0 dBm) <-- This is also kernel fallback
* 2472 MHz [13] (30.0 dBm) <-- Set to 23 instead as that was was above
* 2484 MHz [14] (30.0 dBm)
valid interface combinations:
* #{ managed } <= 2048, #{ AP, mesh point } <= 8, #{ P2P-client, P2P-GO } <= 1, #{ IBSS } <= 1,
total <= 2048, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz }
* #{ WDS } <= 2048,
total <= 2048, #channels <= 1, STA/AP BI must match
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
}}}
ref AREDN->ticket:183
Change-Id: I00e52b80ce5f8e8a774c7bae7d946a6dab73bacf
2016-09-18 17:49:46 +00:00
3962465066
feature: Instruct search engines not to index node pages
...
Provide HTTP header to search engines not to index the page.
Eventually we will likely want to add nofollow and a robots file
but first we need to get this pushed out and into search engine hands
so they delist the entires that may already be cached.
Change-Id: I47a68fcc8fb69c43c3f1bbe2b8a04a3e8d51571a
2016-08-16 18:15:06 -07:00
6bc3999b59
hardware: Rocket M5 with GPS 0xe1c5
...
fixes AREDN->ticket:162
Forum reference: http://www.aredn.org/content/m5-gps
Submitted by KE2N
{{{
board.sysid=0xe1c5
board.cpurevision=0x00000101
board.name=Rocket M5
board.shortname=R5N
board.subtype=GPS
board.netmodes=7
board.hwaddr=00272228652D
board.reboot=50
board.upgrade=150
board.phycount=2
board.phy.1.maxmtu=2024
board.phy.2.maxmtu=2024
board.gps=1
radio.1.name=
radio.1.shortname=
radio.1.bus=pci
radio.1.subsystemid=0xe1c5
radio.1.subvendorid=0x0777
radio.1.txpower.max=27
radio.1.txpower.min=-4
radio.1.txpower.offset=5
radio.1.ieee_modes=5
radio.1.antennas=13
radio.1.def_antenna=13
radio.1.antenna.1.id=1
radio.1.antenna.1.name=AMO-5G10
radio.1.antenna.1.gain=10
radio.1.antenna.1.builtin=0
radio.1.antenna.1.chains=2
radio.1.antenna.1.chain.1.id=0
radio.1.antenna.1.chain.1.name=Vertical
radio.1.antenna.1.chain.2.id=1
radio.1.antenna.1.chain.2.name=Horizontal
radio.1.antenna.2.id=2
radio.1.antenna.2.name=AMO-5G13
radio.1.antenna.2.gain=13
radio.1.antenna.2.builtin=0
radio.1.antenna.2.chains=2
radio.1.antenna.2.chain.1.id=0
radio.1.antenna.2.chain.1.name=Vertical
radio.1.antenna.2.chain.2.id=1
radio.1.antenna.2.chain.2.name=Horizontal
radio.1.antenna.3.id=3
radio.1.antenna.3.name=AM-5G16-120
radio.1.antenna.3.gain=16
radio.1.antenna.3.builtin=0
radio.1.antenna.3.chains=2
radio.1.antenna.3.chain.1.id=0
radio.1.antenna.3.chain.1.name=Vertical
radio.1.antenna.3.chain.2.id=1
radio.1.antenna.3.chain.2.name=Horizontal
radio.1.antenna.4.id=4
radio.1.antenna.4.name=AM-5G17-90
radio.1.antenna.4.gain=17
radio.1.antenna.4.builtin=0
radio.1.antenna.4.chains=2
radio.1.antenna.4.chain.1.id=0
radio.1.antenna.4.chain.1.name=Vertical
radio.1.antenna.4.chain.2.id=1
radio.1.antenna.4.chain.2.name=Horizontal
radio.1.antenna.5.id=5
radio.1.antenna.5.name=AM-M-V5G-Ti
radio.1.antenna.5.gain=17
radio.1.antenna.5.builtin=0
radio.1.antenna.5.chains=2
radio.1.antenna.5.chain.1.id=0
radio.1.antenna.5.chain.1.name=Vertical
radio.1.antenna.5.chain.2.id=1
radio.1.antenna.5.chain.2.name=Horizontal
radio.1.antenna.6.id=6
radio.1.antenna.6.name=AM-5G19-120
radio.1.antenna.6.gain=19
radio.1.antenna.6.builtin=0
radio.1.antenna.6.chains=2
radio.1.antenna.6.chain.1.id=0
radio.1.antenna.6.chain.1.name=Vertical
radio.1.antenna.6.chain.2.id=1
radio.1.antenna.6.chain.2.name=Horizontal
radio.1.antenna.7.id=7
radio.1.antenna.7.name=AM-5G20-90
radio.1.antenna.7.gain=20
radio.1.antenna.7.builtin=0
radio.1.antenna.7.chains=2
radio.1.antenna.7.chain.1.id=0
radio.1.antenna.7.chain.1.name=Vertical
radio.1.antenna.7.chain.2.id=1
radio.1.antenna.7.chain.2.name=Horizontal
radio.1.antenna.8.id=8
radio.1.antenna.8.name=AM-V5G-Ti
radio.1.antenna.8.gain=21
radio.1.antenna.8.builtin=0
radio.1.antenna.8.chains=2
radio.1.antenna.8.chain.1.id=0
radio.1.antenna.8.chain.1.name=Vertical
radio.1.antenna.8.chain.2.id=1
radio.1.antenna.8.chain.2.name=Horizontal
radio.1.antenna.9.id=9
radio.1.antenna.9.name=AM-5AC21-60
radio.1.antenna.9.gain=21
radio.1.antenna.9.builtin=0
radio.1.antenna.9.chains=2
radio.1.antenna.9.chain.1.id=0
radio.1.antenna.9.chain.1.name=Vertical
radio.1.antenna.9.chain.2.id=1
radio.1.antenna.9.chain.2.name=Horizontal
radio.1.antenna.10.id=10
radio.1.antenna.10.name=AM-5AC22-45
radio.1.antenna.10.gain=22
radio.1.antenna.10.builtin=0
radio.1.antenna.10.chains=2
radio.1.antenna.10.chain.1.id=0
radio.1.antenna.10.chain.1.name=Vertical
radio.1.antenna.10.chain.2.id=1
radio.1.antenna.10.chain.2.name=Horizontal
radio.1.antenna.11.id=11
radio.1.antenna.11.name=RD-5G-30
radio.1.antenna.11.gain=30
radio.1.antenna.11.builtin=0
radio.1.antenna.11.chains=2
radio.1.antenna.11.chain.1.id=0
radio.1.antenna.11.chain.1.name=Vertical
radio.1.antenna.11.chain.2.id=1
radio.1.antenna.11.chain.2.name=Horizontal
radio.1.antenna.12.id=12
radio.1.antenna.12.name=RD-5G31-AC
radio.1.antenna.12.gain=31
radio.1.antenna.12.builtin=0
radio.1.antenna.12.chains=2
radio.1.antenna.12.chain.1.id=0
radio.1.antenna.12.chain.1.name=Vertical
radio.1.antenna.12.chain.2.id=1
radio.1.antenna.12.chain.2.name=Horizontal
radio.1.antenna.13.id=13
radio.1.antenna.13.name=RD-5G-34
radio.1.antenna.13.gain=34
radio.1.antenna.13.builtin=0
radio.1.antenna.13.chains=2
radio.1.antenna.13.chain.1.id=0
radio.1.antenna.13.chain.1.name=Vertical
radio.1.antenna.13.chain.2.id=1
radio.1.antenna.13.chain.2.name=Horizontal
radio.1.distance_limit_km=0
radio.1.chanbw="5,8,10,20,30,40"
feature.rssi.leds=2
feature.gps=1
feature.gps.leds=3
feature.ext_reset=0
}}}
Change-Id: I6c03799cc04577b873b7ec04038238fb761ec3e7
2016-06-21 16:13:06 -07:00
061ede3488
Merge branch 'ChaosCalmer' into develop
...
Change-Id: I26a8677595a25aae267b7365f1e5835ea68f49b4
2016-06-19 19:26:12 -07:00
3bae69cc5c
hardware: add NanoBridge M5 0xe235 in testing
...
XM.v5.5# cat /etc/board.info
board.sysid=0xe235
board.cpurevision=0x000000c2
board.name=NanoBridge? M5
board.shortname=NB5
board.subtype=
board.netmodes=7;
board.hwaddr=00156D1EED1F
board.reboot=30
board.upgrade=150
board.phycount=1
board.phy.1.maxmtu=1524
board.phy.2.maxmtu=1524
radio.1.name=
radio.1.shortname=
radio.1.bus=pci
radio.1.subsystemid=0xe235
radio.1.subvendorid=0x0777
radio.1.txpower.max=23
radio.1.txpower.offset=1
radio.1.antennas=3
radio.1.def_antenna=4
radio.1.antenna.1.id=4
radio.1.antenna.1.name=Not specified
radio.1.antenna.1.gain=0
radio.1.antenna.2.id=1
radio.1.antenna.2.name=300
radio.1.antenna.2.gain=22
radio.1.antenna.3.id=2
radio.1.antenna.3.name=400
radio.1.antenna.3.gain=25
fixes AREDN->ticket:161
Change-Id: I050f39646000e4e6ce4342e7140046ba77396d38
2016-05-31 19:56:03 -07:00
1adb471d31
hardware: Mark devices as supported for 3.16.1.0
...
Moving devices that have been tested in beta for 3.16.1.0 to supported status
2016-04-20 17:57:08 -07:00
7d437e2cb8
bug fix: run sysupgrade forked off from uhttpd, kill un-necessary processes and flush page cache during firmware upgrade
2016-03-08 20:29:35 -07:00
5b7475f607
Feature: Add 0xe4a2 boardid support for AirRouter (non-HP)
...
XM.v5.5.11# cat /etc/board.info
board.sysid=0xe4a2
board.cpurevision=0x00000101
board.name=AirRouter
board.shortname=LAP
board.subtype=
board.netmodes=15
board.hwaddr=687251405E66
board.reboot=30
board.upgrade=150
board.phycount=2
board.phy.1.maxmtu=2024
board.phy.2.maxmtu=2024
radio.1.name=
radio.1.shortname=
radio.1.bus=pci
radio.1.subsystemid=0xe4a2
radio.1.subvendorid=0x0777
radio.1.txpower.max=20
radio.1.txpower.offset=1
radio.1.antennas=1
radio.1.def_antenna=4
radio.1.antenna.1.id=4
radio.1.antenna.1.name=Combined
radio.1.antenna.1.gain=0
2016-02-10 20:13:59 -08:00
de2ba6ec59
feature: Add definition for NS Loco M5 0xe0a5
2016-01-10 18:49:58 -08:00
ad8e3c0605
revert validate_hostname change
2016-01-08 18:05:31 -07:00
44ab46bc87
move new settings to optional area under table, disable ntp server, ntp server fqdn validation
2016-01-08 18:04:25 -07:00
7653acc333
Merge branch 'develop' into ntp
2016-01-08 11:11:13 -07:00
6f97c52565
add time zone and ntp server to setup page
2016-01-08 10:58:22 -07:00
cb1bd15823
resized distance field, changed is_online technique
2016-01-06 14:36:40 -06:00
4f2d68bc08
feature: added lat/lon/gridsquare fields and map to capture them
2016-01-06 10:23:18 -06:00
cc6d4ee550
hardware: Add testing support for AirRouter HP
...
board.info
{{{
board.sysid=0xe4b2
board.cpurevision=0x00000101
board.name=AirRouter
board.shortname=LAP
board.subtype=HP
board.netmodes=15
board.hwaddr=687251449BBD
board.reboot=50
board.upgrade=150
board.phycount=2
board.phy.1.maxmtu=2024
board.phy.2.maxmtu=2024
radio.1.name=
radio.1.shortname=
radio.1.bus=pci
radio.1.subsystemid=0xe4b2
radio.1.subvendorid=0x0777
radio.1.txpower.max=28
radio.1.txpower.min=-4
radio.1.txpower.offset=9
radio.1.antennas=1
radio.1.def_antenna=4
radio.1.antenna.1.id=4
radio.1.antenna.1.name=Combined
radio.1.antenna.1.gain=6
}}}
2015-12-28 22:48:13 -08:00
8586a9fee8
feature: device support for older AirGrid M5 0xe245 tested in beta
2015-12-11 10:50:45 -08:00
4aff5d7a59
fixed typos in device names
2015-12-11 11:15:48 -06:00
096f798ceb
hardware: Update supported hardware list labels.
2015-12-10 10:53:37 -08:00
4d12a6f535
feature: include boardid for Rocket M5 XW
2015-11-25 21:54:36 -08:00
0c776ab932
fix: correct max power setting NS loco XW
2015-11-25 21:23:52 -08:00
dc5df00d46
feature: Add boardid for NS Loco M5 XW
2015-11-25 20:43:27 -08:00
ae2bc531b2
hardware: board add: Rocket M5 with USB Port
...
board.info
{{{
board.sysid=0xe105
board.cpurevision=0x000000c2
board.name=Rocket M5
board.shortname=R5N
board.subtype=
board.netmodes=7
board.hwaddr=00156DDC9D53
board.reboot=30
board.upgrade=150
board.phycount=1
board.phy.1.maxmtu=1524
board.phy.2.maxmtu=1524
radio.1.name=
radio.1.shortname=
radio.1.bus=pci
radio.1.subsystemid=0xe105
radio.1.subvendorid=0x0777
radio.1.txpower.max=27
radio.1.txpower.offset=5
radio.1.antennas=1
radio.1.def_antenna=4
radio.1.antenna.1.id=4
radio.1.antenna.1.name=Combined
radio.1.antenna.1.gain=0
}}}
2015-07-23 21:24:21 -07:00
108e05088b
bugfix: Add max power level tracking control for per channel power on devices
...
Mainly relates to TP-Link devices which have a roving power level programmed into the hardware.
The datasheets for the hardware may say higher power but the chip has been programmed to not go above these values.
2015-07-20 23:30:49 -07:00
9b30e157bc
bugfix: Set max power for device to TPLink programed "max power"
...
This is the absolute maximum that can be used by the device from TPLink eprom programming.
The value actually goes down on some frequencies.
2015-07-20 21:38:01 -07:00
8eabf6ad00
bugfix: snr setting was setting SignalLevel instead of NoiseLevel
...
ref AREDN->ticket:129
2015-07-02 22:43:01 -07:00
c4c808f98c
Merge branch 'FixupRefDMZLed' into release-3.15.1.0
...
Remove references to DMZ led and replace with "Status 4" led
2015-07-01 23:25:56 -07:00
a46bbf27d8
bugfix: sometimes iw doesn't show noise floor
...
Pull from kernel debug instead for now untill we can work around it in iw.
fixes AREDN->ticket:129
2015-07-01 10:05:58 -07:00
13db1b02a2
bugfix: Remove ref to DMZ Led on first node reboot
2015-06-30 08:36:45 -07:00
39729157c6
bugfix: Signal levels do not show up on "new extended" RF Channels
...
Switch to iw over iwinfo because it handles the new channels better.
Partially reverts changeset:808a8d5019fce4a7ca2c027ea7838d43c6d8cad0/aredn_ar71xx
fixes AREDN->ticket:129
2015-06-30 00:05:45 -07:00
f915225459
bugfix: Add in-testing support for older NanoStation M5 XW boards
...
board.info provided by VE3KMV
{{{
board.sysid=0xe005
board.cpurevision=0x000000c2
board.name=NanoStation M5
board.shortname=N5N
board.subtype=
board.netmodes=7
board.hwaddr=00272232336C
board.reboot=30
board.upgrade=150
board.phycount=2
board.phy.1.maxmtu=1524
board.phy.2.maxmtu=1524
radio.1.name=
radio.1.shortname=
radio.1.bus=pci
radio.1.subsystemid=0xe005
radio.1.subvendorid=0x0777
radio.1.txpower.max=27
radio.1.txpower.offset=5
radio.1.antennas=1
radio.1.def_antenna=4
radio.1.antenna.1.id=4
radio.1.antenna.1.name=Combined
radio.1.antenna.1.gain=16
}}}
2015-06-21 19:24:43 -07:00
21edf5fa02
bugfix:Let kernel handle antenna selection: Remove antenna name mapping data.
2015-06-18 20:18:03 -07:00
ea9dfc5d1a
bugfix: Let kernel handle antennas:Remove sub functions wifi_validant and wifi_defaultant
2015-06-18 20:15:47 -07:00
1b68255c7f
hardware: NanoStation M3: Set NanoStation M3 to "in testing"
...
25dbm max power, with 3dbm offchip amplifier.
ref AREDN->ticket:53
2015-05-21 10:51:58 -07:00
42ee986cd3
bugfix: Untill user visit status page theme is not set.
...
Move default theme selection to html_header() to solve theme not being set.
2015-05-14 11:36:51 -07:00
d59709d840
bugfix: Theme reverts to no-theme when status page reset button is pressed.
...
A symlink loop occurs because the default theme selector links back to itself.
Removing the value= on the select title entry prevents this.
2015-05-14 10:56:41 -07:00
c26b5fd992
Merge branch 'tunnel_mainline' into develop
2015-05-07 19:25:14 -05:00
bd3de68231
ar71xx: hardware: NanoBeam-M5-19 Add testing support
...
Add NanoBeam M5 19 in testing support
2015-05-05 16:29:53 -07:00
2af1e3e0c3
ar71xx: Copy get_model to get_boardid and modify to return a boardid
...
When model exiss that has a boardid in EEPROM it will return from there, otherwise it returns the model as chosen by ar71xx
2015-05-05 16:18:24 -07:00
7327c2de51
Merge branch 'develop' into tunnel_mainline
2015-04-23 23:00:00 -05:00
9840db43de
hardware: Add CPE210 in testing support
2015-04-22 11:31:23 -07:00
14ddd34906
Merge branch 'RocketM3' into develop
...
RocketM3 will remain in untested status until we get spectrum report.
ref AREDN->ticket:53
2015-04-22 00:06:43 -07:00
344992b096
Merge commit '714a3d6f5404bcd650019bd59e92d2cc2bb54164' into develop
2015-04-17 18:50:53 -05:00
ff057d3488
bugfix: change navbar spacing to accomodate tunnels
2015-04-08 19:59:39 -05:00
c40a42562f
feature: implement vtundsrv startup script. make 13-vtun vtund aware
2015-04-08 00:15:36 -05:00
82611bb57e
bugfix: NanoStation M5 XW device config was malformed
...
ref AREDN->ticket:43
2015-04-07 22:11:56 -07:00
54210a2d7e
Merge branch 'develop' of ssh://git.aredn.org/aredn_ar71xx into tunnel_mainline
2015-04-07 23:09:29 -05:00
853430dbdf
hardware: Add testing support for NanoStation M5 XW
...
ref: AREDN->ticket:43
2015-04-07 20:37:58 -07:00
e6d08f5606
merged from develop
2015-04-07 10:36:42 -05:00
928e7e720a
Merge branch 'develop' of ssh://git.aredn.org/aredn_ar71xx into dyn_css
2015-04-06 23:20:12 -05:00
f6f3aaef9e
Merge branch 'TPLinkCPE' into develop
2015-04-06 21:14:39 -07:00
09af80b17e
check for .css file extension being passed
2015-04-06 14:47:09 -05:00
b8dcc50fb9
changed help text
2015-04-06 09:43:05 -05:00
63bb07b617
hardware: CPE510: Add initial hardware support for TPLink CPE510 in testing
...
Testing mode for CPE510
Offset needs to be looked into, OS reports a max power of 23dbm need to see if this is kernel, or offset related.
Should provide enough details for the board to be registered in the UI
2015-04-05 22:16:24 -07:00
7c152d7c1e
hardware: Expand board_id routine to allow TPLink devices to be obtained
...
When a device does not have a subsystem device ID we will fall back to the board_detect routine.
In the case of a TPLink CPE510 the model will be along the lines of "TP-Link CPE510 v1.0"
In the case of TPLink CPE510 this also includes a hardware version so should the hardware be changed in the future we will be able to key off that as well.
2015-04-05 22:07:47 -07:00
df0bc42208
feature: converted css to use symlinks and multiple files
2015-04-05 21:19:32 -05:00
6672996cd3
added ability to have multiple css files
2015-04-04 23:49:31 -05:00
b074fd6985
consolidated functions to reduce duplication (save space)
2015-04-01 17:26:52 -05:00
2461d4acd8
add vpn and vpnc pages to UI menu
2015-04-01 17:09:18 -05:00
5414cb2f86
bugfix: Correct bandmapping to 3400 for Rocket M3
2015-03-31 23:50:05 -07:00
6c91ec0ab4
Add channels that are within normal 5.8GHz unit range for Rocket M3 usage.
...
M3 is a 5.8GHz unit with a 2GHz offset transverter.
5MHz width is recomended on these channels.
Send to spectrum analysis for verification that output looks clean.
Stepping stone to working on the wider width of the full 3.4GHz band which has more channels but unlike channels 95-100 (added in this commit) the rest are outside the normal 5.8GHz cal range (but are between two cal points so may be fine)
2015-03-31 23:42:22 -07:00
16576d7bde
bugfix: dtdlink is by default on eth0.2 not eth0.1
2015-03-26 16:47:33 -07:00
0d11af70b9
bugfix: Unknown interfaces wouldn't return default interface.
2015-03-26 01:31:50 -07:00
9444716fbd
feature: Add function and code to UI code to prepare for changing interface names in the core OS.
...
Create get_interface which will lookup in the current uci network config the realname for the logical interface name.
When the interface is not found it will fall back to a hard coded list.
Configure the UI to use the new get_interface function.
2015-03-24 23:25:18 -07:00
e146193b65
Rerand from BBHN to AREDN(TM)
...
Since a large number of the BBHNDev team has decided to create firmware fully independent of the BBHN Project the decision has been made to rebrand the firmware to differentiate from the origional BBHN work.
We would like to thank all those whom have worked on the BBHN firmware over the years and all those who continue to work on the firmware under AREDN(TM).
2015-03-09 16:39:04 -07:00
5c3ee1d068
bugfix: Add GPLv3 license text to core BBHN Mesh files
...
Program went GPLv3 last year but license text was never added to files
Default text to give credit to David as he is listed in all commits and to reference the BBHN Austin team at the same time as they were part of the group of HAM's that started this project.
2015-01-18 11:36:49 -08:00
917573cf95
hardware:bugfix: AirGrid M2 0x212 remove power offset to facilitate testing
...
Removing the offset and increasing max power so we have full range avaliable to us.
This may not help us figure out the offset but will allow us a wider range of options.
ref BBHN->ticket:71
2014-12-14 10:54:05 -08:00
b7dcfdd9ce
hardware 🆕 Add testing support for AirGrid M2 0xe212
...
Reported information and board information do not appear to line up, device will need further testing to verify actual details.
Max Power and Power Offset are of concern.
ref BBHN->ticket:71
2014-12-14 10:37:48 -08:00
d5af5c97cf
support status: Mark Rocket M9 as supported.
2014-11-03 20:26:47 -08:00
5a39316a7e
hardware: support: Loco M9, NanoBridge M9 test: RocketM9
...
tag NanoStation Loco M9 and NanoBridge M9 into supported status
begin testing Rocket M9 support
ref BBHN->ticket:66
fixes BBHN->ticket:51
2014-10-20 19:45:46 -07:00
32a67e1b2c
Add initial testing support for M9 devices
...
ref BBHN->ticket:51
2014-07-14 23:01:16 -07:00
88d532a3a1
bugfix: get_default_gw needs to follow the route the node will use to internet.
...
because of previous bugfix the function needs to check table 31 and 254 (with 254 taking priority)
2014-07-08 00:02:47 -07:00
2a8692d5a0
Update list of tested devices.
...
Officaly now supporting (XM series only for all the below):
{{{
Rocket M5
Bullet M5
AirGrid M5
NanoBridge M2
AirGrid M2
AirGrid M5 HP
NanoBridge M5
Bullet M2 Titanium
Bullet M5 Titanium
PicoStation M2
NanoStation M5
NanoStation Loco M5
}}}
2014-06-24 21:05:13 -07:00
d6bb48154a
Resolve issue related to returning the offset used by iwinfo
2014-05-06 14:29:19 -07:00
207c0f738f
Adjust usage of wifi_txpoweroffset() to handle the fact that offset may be set already in iwinfo so we need to read that value first.
...
Made adjustmetns to code that calls wifi_txpoweroffset() to ensure we minimize the number of calls that spawn a shell.
Also adjust the setting of $wifi_txpower to handle the fact that iwinfo returns the known offset.
2014-05-02 12:07:19 -07:00
808a8d5019
Initial changes to work with OpenWRT 12.09
...
Mostly relates to iwinfo being the new command to obtain info about devices.
iwlist does not exist in 12.09
2014-05-01 20:32:40 -07:00
0541234e1e
Assign 2.4ghz devices to 2400 band.
...
Fixup bug in channel mapping (leading 0 in channel number doesn't work)
ref BBHN->ticket:29
2014-04-19 23:51:55 -07:00
f83bebe58a
Add testing support for PicoStation2 PicoStation2 HP and AirGrid M2 HP (0xe242)
...
ref BBHN->ticket:40 and BBHN->ticket:41
2014-04-18 20:10:43 -07:00
06febced7f
Add testing support for Bullet M5 TI
...
see BBHN->ticket:29
2014-04-12 09:48:06 -07:00
7a0de5a6a9
Add line in changeset:bbhn_ar71xx/a4dd9a9bdd798b05d76d71d135d860f57cb83d8d
...
Add support for dtdlink_* variables
2014-04-08 23:28:29 -07:00
a4dd9a9bdd
Add new feature device-to-device linking (dtdlink)
...
The dtdlink interface is vlan 2 on eth0 and is used for linking two or more devices together.
This will allow for band-to-band repeaters, sector antenna setups, etc.
see BBHN->ticket:28
2014-04-08 23:19:45 -07:00
ede5b0656d
Better validation of services advertisements entries
...
fixes BBHN->ticket:35
2014-04-01 15:30:55 -07:00
e34b7fcee4
Fix issue where the active SSID does not timeout in iwlist so networks show up after they have disappeared.
...
fixes BBHN->ticket:30
2014-03-31 22:59:47 -07:00
c6a3e7a64e
Add testing support for multiple 2.4ghz Ubiquiti devices
...
see BBHN->ticket:31, BBHN->ticket:32, BBHN->ticket:36, BBHN->ticket:38
2014-03-27 23:19:13 -07:00
3b215c40c0
Initial code for 5GHZ (and other band) devices.
...
Includes band/channel mapping
Code to set default RF channel on first boot
Add many 5ghz Ubiquiti devices in a testing phase including:
NanoBeam M5 (Intl), NanoBridge M5, AirGrid M5 HP, AirGrid M5, NanoStation M5, NanoStation Loco M5, Bullet M5, Rocket M5
see BBHN->ticket:29
2014-03-27 22:53:06 -07:00
f6d81b25c2
Add support for devices that are 'in testing' to the banner display.
...
In testing devices should be listed with a -2 status
2014-03-26 21:47:54 -07:00
e1c28ab634
Decrease maxpower NanoStation Loco M2
...
Failed to put in changeset:16b4c2a/bbhn_ar71xx to correct for the increased txpower
2014-01-19 18:50:17 -08:00
532605354c
Set tested devices to supported
...
airGrid M2, NanoStation M2, NanoStation Loco M2 are now officaly supported
fixes BBHN->ticket:12, BBHN->ticket:25
ref BBHN->ticket:11
2014-01-19 18:44:01 -08:00
16b4c2a201
Increae txoffset for NanoStation Loco M2
...
Based on testing airOS claims NSLM2's have a 2db amplifier it appears that they may actually have a 5db amp.
Since units keep reporting 3db lower than we expect them to we are increasing the txpower offset until we have confirmed power tests.
fixes BBHN->ticket:11, BBHN->ticket:22
2014-01-19 18:38:26 -08:00
fc1d9fbc02
hardware_info fixups NanoStation M2 NanoStation Loco M2 and default chains
...
Set default of using chains as more devices being presened rely on chains than those who don't.
Fixed the default antenna and chain support on NanoStataton M2 and NanoStation Loco M2
2014-01-14 10:33:38 -08:00
cef893bf59
NanoStation M2 should use chains
...
see BBHN->ticket:25
2014-01-12 23:05:50 -08:00
72a4882a09
Add testing support for NanoStation M2
...
28dbm after the final with a 10db amplifier. Uses chains.
see BBHN->ticket:25
2014-01-10 20:15:38 -08:00
e6d5ce7559
Add extra details on NanoBridge M3
2014-01-09 10:51:00 -08:00
ccb83c6a91
fix olsrd-config not putting in ip to name mapping
...
nslookup has changed between upstream Linksys build and our Backfire based UBNT build.
fixes BBHN->ticket:21
2013-12-31 12:38:17 -08:00
b0b04d23d8
Model Name correction on Bullet M2 HP
2013-12-16 10:56:36 -08:00
1f49e57e54
Add testing support for ariGrid M2 HP
...
airGrid M2 HP -- 28dbm output power device with a 9dbm offset.
see BBHN->ticket:12
2013-12-15 13:09:11 -08:00
3c4eee4f0f
Add testing support for NanoStation Loco M2
...
Added NanoStation Loco M2
board.sysid=0xe0a2
radio.1.txpower.max=23
radio.1.txpower.offset=2
radio.1.antennas=1
Chains are not 100% guranteed to be accurate.
Belive from http://community.ubnt.com/t5/airOS-Software-Configuration/chain-0-1/td-p/140354
that Chain0 is Vertical Chain1 Horizontal when mounted vertically
Chain Mask is pulled from the Rocket M mask as this is the only sample
we have in the database.
see BBHN->ticket:11
2013-12-13 22:15:40 -08:00
7a28c18bfd
Refactor code for better hardware managment
...
Refactor to create a central hash matrix that provides details on
devices.
The if else else else tree was going to get very messy based on
the realization that each device has custom attributes and the
need to provide diffrent settings for each unit.
Allows easier managment long term.
2013-12-13 21:59:34 -08:00
Conrad Lara - KG6JEI