Allows nodes to default to a common channel that is in the most common bandplan space for Part 97 usage.
Local cordination is still needed by users to make sure the channel matches the local deployment.
Defaults are as follows:
Band : Channel Freq : Bandwidth
900 : 912MHz : 5MHz
2400 : 1 2412MHz : 20MHz
3400 : 3420MHz : 5MHz
5800 : 149 5745MHz : 5MHz
2.4GHz keeps channel 1 at 20MHz because it is the standard deployment.
All other bands are still 'new' and no standard exist so we are creating one.
5MHz chosen because it better fits the emcomm goal. Smaller width should be stronger allowing for better networks.
Local networks can change as they see fit.
Remove setting RF channel on first boot in uci-defaults.
This should allow the node to use standard wifi channels when it boots allowing mesh setup to be run from a laptop or mobile device.
We will later move them to a real mesh channel during the mesh setup page.
Should also resolv issue where nodes were booting up on channel -2 and similar and wifi would refuse to start due to regdomain.
Config file is present upon initial start and in mesh mode.
Daemon still starts up in other modes but will not function w/o settings.
Firewall:
Permit access for UDP:161 (SNMPD) on WIFI and DTDLINK
Lan is permitted by default allow rules.
Makes the nodes advertise using DHCP Options 121 and 249 routes to the mesh (10.0.0.0/8) and the reserved (172.16.0.0/12) address ranges.
This change allows directing systems to prefer the mesh node for mesh ranges unless another network rule is more specific (such as a directly connected network)
This is mostly useful where a PC may have multiple network connections active as it improves the desire for the packets to travel via the mesh network.
Currently the:
10.0.0.0/8 range is used by mesh nodes and dtdlinking of mesh nodes.
172.27.0.0/16 is used for default LAN network on NAT nodes.
172.33.0.0/16 is for ad-hoc tunnels
All others in the advertised range are reserved for future network use.
Under Barrier Breaker sometimes OLSRD gets started before any interface is up causing OLSRD to shutdown because no interfaces exist.
Forces OLSRD to stay on and wait for the interfaces to come online.
Nodes sometimes show up as a mid1 entry when dtdlink and RF connected.
Sometimes the nodes will get the eth0 ip because wlan0 is not up yet.
Under Barrier Breaker the MainIP option is now supported as part of the uci system which allows us to restore using this setting.
We can now force the IP address that is claimed (wlan0) for the primary IP of the node.
Since a large number of the BBHNDev team has decided to create firmware fully independent of the BBHN Project the decision has been made to rebrand the firmware to differentiate from the origional BBHN work.
We would like to thank all those whom have worked on the BBHN firmware over the years and all those who continue to work on the firmware under AREDN(TM).
When a non mesh-gw node has a route via the WAN interface and through a mesh-gw it will choose the mesh-gw instead of the local WAN connection.and
We change the routing list to prefer the WAN link.
When the WAN is static configured the user will need to disable the WAN interface for the mesh internet to be chosen.
When the WAN is configured to dynamic the loss of a DHCP lease will allow the node to chose the remote mesh internet.
The simple solution would be to change the WAN to disabled and reboot to ensure a remote node is used instead if the local internet fails.
Thanks to Joe AE6XE and Clint AE5CA for pointing out this scenario.
By checking the "Keep Settings" box the node will run sysupgrade instead of mtd. Core settings are stored between installs and the _setup files are updated by pulling in missing items from the _setup.default files.
Using a press of around 5 seconds (3-7) the node will reset the passord to BBHN default and enable dhcp on the lan interface.
A press of around 10 seconds (8-12) will cause the node to reset the node to 'just flashed' status and cause the node to reboot.
Due to multiple issues that olsrd secure seems to make occur more often (but is not soley caused by OLSR Secure) causing olsr to crash olsr secure is being pulled while we work on the module.
This partialy reverts commit 553c126490.
tag: RequiresProtocolIncrement
Conrad Lara - KG6JEI