Mirrors
/
aredn
mirror of https://github.com/aredn/aredn.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
aredn/README.md

16 KiB
Raw Blame History

Amateur Radio Emergency Data Network AREDN(tm) Firmware

http://www.arednmesh.org

About AREDN

AREDN wireless networks are deployed by licensed Amateur Radio operators, Technician Class or higher, under FCC Part 97 allocations adjacent to FCC part 15, unlicensed, WIFI, allocations. They are configured as ad-hoc nodes to form mesh networks. The firmware created below enables the effective use of valuable and dedicated frequencies for communication services to government and private relief organizations in times of disaster or other emergencies.

Amateur Radio frequencies are relatively clean of noise from the commercial allocations and ensure usability for Amateur Radio Operators. This firmware enables 802.11n wireless networks to be created and expanded with minimal to no pre-planning or IT expertise. A user can deploy a 'node' anywhere to connect in and extend an AREDN network. Device hardware options exist to provide sector coverage, build point-to-point links, and connect end point services to the network. High speed link rates are routinely achieved over long distances, e.g. 60Mbps+ on 10MHz channels over 80km links.

For further information on obtaining an Amateur Radio Technician Class license, please refer to http://www.arrl.org/getting-your-technician-license

Usage Information

What to know about the images built with the instructions below

This is the active 'main' branch with latest AREDN code. At anytime a new change may be broken or break prior capabilities.

The Amateur Radio community is encouraged to participate in loading the images produced from a "nightly build" and run the AREDN firmware in a variety of environments. Given new features may not yet be documented, participants should already have a basic knowledge of Linux and Networking to understand and provide useful feedback to the Developer submitting the code.

The goal of participation is to obtain confidence that new features and the overall mesh node is stable. The more participation, the earlier an issue is found, the faster an enhancement will be turned into a release.

Please refer to https://github.com/aredn/aredn/issues for a list of outstanding defects.

Images built

Device Target Image RAM Stability
AirGrid XM ath79 ubnt_bullet-m-ar7241 32MB untested sunset
AirGrid XW ath79 ubnt_bullet-m-xw 32MB untested sunset
AirRouter ath79 ubnt_airrouter 32MB untested sunset
AirRouter HP ath79 ubnt_airrouter 32MB untested sunset
Bullet M2Ti/M5/M5Ti ath79 - 32MB untested sunset
Bullet M2 ath79 ubnt_bullet-m-ar7241 32MB stable sunset
Bullet M2 XW ath79 ubnt_bullet-m-xw 64MB untested
LiteBeam AC5 Gen2 ath79 ubnt_litebeam-ac-gen2 64MB stable new
LiteBeam M5 ath79 - 64MB untested
NanoBeam AC 5 ath79 ubnt_nanobeam-ac 64MB untested new
NanoBeam AC 5 Gen 2 ath79 ubnt_nanobeam-ac-gen2 128MB stable new
NanoBeam M2-13/M5-16/M5-19 ath79 - 32MB untested sunset
NanoBridge 2G18 ath79 ubnt_nanobridge-m 32MB untested sunset
NanoBridge 5G22/25 ath79 ubnt_nanobridge-m 32MB untested sunset
NanoBridge M9 ath79 ubnt_nanobridge-m 32MB untested sunset
NanoStation AC 5 ath79 ubnt_nanostation-ac 64MB stable new
NanoStation Loco M2/M5/M9 XM ath79 ubnt_nanostation-loco-m 32MB untested sunset
NanoStation Loco M2 XW ath79 ubnt_nanostation-loco-m-xw 64MB untested
NanoStation Loco M5 XW ath79 ubnt_nanostation-loco-m-xw 64MB stable
NanoStation M2/M3/M5 XM ath79 ubnt_nanostation-m 32MB stable sunset
NanoStation M2/M5 XW ath79 ubnt_nanostation-m-xw 64MB stable
PicoStation M2 ath79 ubnt_picostation-m 32MB untested sunset
PowerBeam AC 5 500 ath79 ubnt_powerbeam-5ac-500 128MB stable new
PowerBeam-M2-400 ath79 ubnt_powerbeam-m2-xw 64MB untested
PowerBeam-M5-300 ath79 ubnt_powerbeam-m5-300 64MB stable
PowerBeam-M5-400/400ISO/620 ath79 ubnt_powerbeam-m5-xw 64MB stable
PowerBridge ath79 ubnt_powerbridge-m 64MB untested
Rocket AC Lite 5 ath79 ubnt_rocket-5ac-lite 128MB stable new
Rocket M9/M2/M3/M5/M5GPS XM ath79 ubnt_rocket-m 64MB stable
Rocket M2/M5 XM with USB port ath79 ubnt_rocket-m 64MB untested
Rocket M2 XW ath79 ubnt_rocket-m-xw 64MB untested
Rocket M5 XW ath79 ubnt_rocket-m-xw 64MB stable
Rocket M2 Titanium TI ath79 - 64MB untested
Rocket M2 Titanium XW ath79 ubnt_rocket-m-xw 64MB untested
Rocket M5 Titanium TI ath79 - 64MB untested
Rocket M5 Titanium XW ath79 ubnt_rocket-m-xw 64MB stable
TPLink CPE210 v1.X ath79 tplink_cpe210-v1 64MB stable
TPLink CPE210 v2.0 ath79 tplink_cpe210-v2 64MB stable
TPLink CPE210 v3.0 ath79 tplink_cpe210-v3 64MB untested
TPLink CPE220 v2.0 ath79 tplink_cpe220-v2 64MB untested
TPLink CPE220 v3.0 ath79 tplink_cpe220-v3 64MB untested
TPLink CPE510 v1.X ath79 tplink_cpe510-v1 64MB untested
TPLink CPE510 v2.0 ath79 tplink_cpe510-v2 64MB stable
TPLink CPE510 v3.0 ath79 tplink_cpe510-v3 64MB stable
TPLink CPE605 v1.0 ath79 tplink_cpe605-v1 64MB untested
TPLink CPE610 v1.0 ath79 tplink_cpe610-v1 64MB untested
TPLink CPE610 v2.0 ath79 tplink_cpe610-v2 64MB untested
TPLink CPE710 v1.0 ath79 tplink_cpe710-v1 128MB stable new
TPLink WBS210 v1.0 ath79 tplink_wbs210-v1 64MB untested
TPLink WBS210 v2.0 ath79 tplink_wbs210-v2 64MB untested
TPLink WBS510 v1.0 ath79 tplink_wbs510-v1 64MB untested
TPLink WBS510 v2.0 ath79 tplink_wbs510-v2 64MB untested
Mikrotik Basebox RB912UAG-2HPnD ath79 mikrotik_routerboard-912uag-2hpnd 64MB untested
Mikrotik Basebox RB912UAG-5HPnD ath79 - 64MB untested
Mikrotik hAP ac lite 952Ui-5ac2nD ath79 mikrotik_routerboard-952ui-5ac2nd 64MB stable
Mikrotik RBLHG-2nD(-XL) ath79 mikrotik_routerboard-lhg-2nd 64MB stable
Mikrotik RBLHG-5nD ath79 mikrotik_routerboard-lhg-5nd 64MB stable
Mikrotik RBLHG-5HPnD(-XL) ath79 mikrotik_routerboard-lhg-5nd 64MB stable
MikroTik RBLHGG-5acD(-XL) ipq40xx mikrotik_lhgg-5acd 256MB stable new
Mikrotik RBLDF-2nD ath79 - 64MB untested
Mikrotik RBLDF-5nD ath79 - 64MB untested
Mikrotik QRT5 RB911G-5HPnD-QRT ath79 - 64MB untested
Mikrotik mANTBox RB911G-2HPnD ath79 - 64MB untested
Mikrotik mANTBox RB911G-5HPnD ath79 - 64MB untested
Mikrotik mANTBox RB912UAG-2HPnD ath79 mikrotik_routerboard-912uag-2hpnd 128MB untested
Mikrotik mANTBox RB912UAG-5HPnD ath79 mikrotik_routerboard-912uag-5hpnd 128MB stable
Mikrotik mANTBox RB921GS-5HPacD 15s ath79 mikrotik_routerboard-921gs-5hpacd-15s 128MB stable new
Mikrotik mANTBox RB921GS-5HPacD 19s ath79 mikrotik_routerboard-921gs-5hpacd-19s 128MB stable new
Mikrotik SXTsq 5HPnD ath79 mikrotik_routerboard-sxt-5nd 64MB stable
Mikrotik SXTsq 5nD ath79 mikrotik_routerboard-sxt-5nd 64MB stable
Mikrotik SXTsq 2nD ath79 - 64MB untested
MikroTik RouterBOARD D52G-5HacD2HnD ipq40xx mikrotik_hap-ac2 128MB stable new
MikroTik RouterBOARD D53iG-5HacD2HnD ipq40xx mikrotik_hap-ac3 256MB stable new
MikroTik RouterBOARD SXTsqG-5acD ipq40xx mikrotik_sxtsq-5-ac 256MB stable new
GL.iNet GL-AR150 ath79 glinet_gl-ar150 64MB stable
GL.iNet GL-USB150 ath79 glinet_gl-usb150 64MB stable
GL.iNet GL-AR300M16 ath79 glinet_gl-ar300m 64MB stable
GL.iNet GL-AR300M w/ 128MB NAND ath79 - 64MB untested
GL.iNet GL-AR750 ath79 glinet_gl-ar750 128MB stable
Meraki MR-16 ath79 - 64MB brick

Stability

  • brick - this image has been tested and will currently brick your hardware. Avoid for now.
  • untested - this image has not been tested on hardware. It may or may not work.
  • stable - this image has been tested on hardware. There may still be bugs.
  • sunset - this device has been sunsetted and support will be deprecated at some point.
  • new - this device is newly supported.

The 'target' is a directory to find the image on at http://downloads.arednmesh.org

Latest Mikrotik installation options are found at: https://www.arednmesh.org/content/installation-instructions-mikrotik-devices

Ethernet Port usage

The standard Ethernet port of an AREDN device uses the following vlan tags. An 802.1Q switch is necessary to utilize the vlan tagged networks:

  • untagged: LAN devices - laptop, ipcam, voip phone, etc.
  • vlan 1: WAN - gateway to connect AREDN network to home network and/or internet (some devices support changing this vlan to an alternate value)
  • vlan 2: DtDLink (device to device) - AREDN network routing between nodes, typically cross band

The following devices have enhanced Ethernet port usage. A single cat5 to the device could be plugged into ether the 'main' or 'secondary' port with standard port functionality. Both ports can be used interchangeably and simultaneously with LAN devices on both ports at the same time.

If the device's hardware supports POE (Power Over Ethernet) pass-through from main port to secondary port, an Advanced Setting option will show to turn on/off. This is useful to power ipCams or other mesh nodes by daisy chaining the network cable from one device to another. Then only one network cable may be needed to reach 2 or 3 devices on the tower. Be sure to check the power capacity in the vendor specifications to not exceed. The first device in the chain will provide the DHCP address to all LAN devices on all nodes (because it powers up first).

  • NanoStation M2 XW
  • NanoStation M5 XW
  • NanoStation M2 XM
  • NanoStation M3 XM
  • NanoStation M5 XM
  • TP-Link CPE210 v1/v1.1
  • TP-Link CPE220 v2
  • TP-Link CPE220 v3
  • TP-Link CPE510 v1/v1.1
  • TP-Link WBS210 v1
  • TP-Link WBS210 v2
  • TP-Link WBS510 v1
  • TP-Link WBS510 v2

The Mikrotik hAP AC Lite, Ubiquiti AirRouter, and AirRouter HP are pre-configured with the following VLANs:

  • Port 1: WAN Port - Packets in/out of this port are expected to be untagged. The node is (by default) configured to receive a DHCP assigned address from a home network, internet, or other foreign network.
  • Port 5: DtDLink Port Mesh Routing -- Connect to another mesh node or 8021.q switch. Packets in/out of this port must be vlan 2 tagged, other packets are ignored.
  • Ports 2-4: LAN devices -- Packets in/out of this port are expected to be untagged. The mesh node will (default) DHCP assign an IP address to your computer, ipCam, voip phone, etc. connected to these ports.

The GL.iNet GL-AR150 and GL-AR300M16 are pre-configured with the following VLANS:

  • Port labeled "WAN": untagged = AREDN WAN
  • Port labeled "LAN": untagged = AREDN LAN, vlan 2 = DtDLink (device to device)

The GL.iNet GL-AR750 is pre-configured with the following ports, left to right:

  • Left Port with internet globe icon: WAN (untagged)
  • Middle Port with "<..>" icon: DtDLink (vlan 2)
  • Right Port with "<..>" icon: LAN (untagged)

IMPORTANT: For Gl.iNet devices, when initially installing AREDN on OpenWRT, you MUST uncheck the "Keep Settings" checkbox.

Submitting Bug Reports

Please submit all issues to http://github.com/aredn/aredn/issues

Developer Only Information

The AREDN firmware is based on OpenWrt with additional packages and patches. A Makefile automates the entire process to create firmware images.

Building with Docker

Installing the Docker environment on your windows/linux/mac machine is a pre-requisite. A docker 'container' has been pre-configured with an aredn linux build environment. Alternative instructions are below if you wish to setup your linux install with the compiler pre-requisites necessary to do the build.

To build with docker:

docker pull arednmesh/builder
docker run -it --name builder arednmesh/builder

To pull an image (or any other file) out of the docker container:

docker cp builder:/opt/aredn/aredn/firmware/targets/ath79/generic/<image>.bin <local directory>

Build Prerequisites

Please take a look at the OpenWrt documentation for a complete and up to date list of packages for your operating system.

On Ubuntu/Debian:

apt-get install git subversion build-essential libncurses5-dev \
  zlib1g-dev gawk unzip libxml-perl flex wget gettext quilt \
  python libssl-dev shellcheck lua5.1

On openSUSE:

zypper install --type pattern devel_basis
zypper install git subversion ncurses-devel zlib-devel gawk unzip \
  perl-libxml-perl flex wget gettext-runtime quilt python \
  libopenssl-devel shellcheck lua51

On Arch:

pacman -S base-devel subversion zlib unzip perl-xml-libxml wget \
  quilt openssl shellcheck lua51 git

Building firmware images

To obtain the source and build the firmware locally use:

bash
git clone https://github.com/aredn/aredn.git
cd aredn
vi config.mk # enter your callsign, etc.
# build default legacy ath79 target ubnt and tplink images
make  
# build and add legacy ath79 target mikrotik images
make SUBTARGET=mikrotik
# build and add ath79 target (latest linux kernel) ubnt, tplink, and gl images
make MAINTARGET=ath79

Building the images may take minutes or hours depending on the machine. For more details see build options.
Review the build options in config.mk: -j <nuMBer of cores + 1>. V=s will give more verbose error messages.

An internet connection is required during the build process. A good internet connection can improve the build time.

You need approximately 10GB of space for the build.

How to build prior builds of AREDN

Prior AREDN images can be rebuilt. Replace one of the following after the "cd aredn" command above:

AREDN release 3.22.12.0

git checkout 3.22.12.0

AREDN release 3.22.8.0

git checkout 3.22.8.0

AREDN release 3.22.6.0

git checkout 3.22.6.0

AREDN release 3.22.1.0

git checkout 3.22.1.0

AREDN release 3.21.4.0

git checkout 3.21.4.0

AREDN release 3.20.3.1

git checkout 3.20.3.1

AREDN release 3.20.3.0

git checkout 3.20.3.0

AREDN release 3.19.3.0

git checkout 3.19.3.0

AREDN release 3.18.9.0

git checkout 3.18.9.0

AREDN release 3.16.2.0

git checkout 3.16.2.0

AREDN release 3.16.1.1

git checkout 3.16.1.1-make

AREDN build 176

git checkout 91ee867

Return to most current changes

git checkout main

Directory Layout

Included in the git Repo:
config.mk    <- build settings
openwrt.mk   <- which openwrt repo and branch/tag/commit to use
feeds.conf/  <- custom package feeds (edit to point to your clone of aredn_packages)
files/       <- file system in AREDN created images, most customizations go here
patches/     <- patches to openwrt go here 
scripts/     <- tests and other scripts called from the build 
configs/     <- definitions of features in the devices' kernel and what packages to include
Makefile     <- the build definition
README.md    <- this file

Created by the build:
openwrt/     <- cloned openwrt repository
firmware/    <- the build will place the images here
results/     <- code checks and other test results in jUnit xml format

Patches with quilt

The patches directory contains quilt patches applied on top of the openwrt git repo defined in config.mk.

If a patch is not yet included upstream, it can be placed in the patches directory with the quilt tool. Please configure quilt as described in OpenWrt Quilt.

Add, modify or delete a patch

Switch to the openwrt directory:

cd openwrt

Now you can use the quilt commands.

Example: add a patch
quilt push -a                 # apply all patches
quilt new 008-awesome.patch   # tell quilt to create a new patch
quilt edit somedir/somefile1  # edit files
quilt edit somedir/somefile2
quilt refresh                 # creates/updates the patch file

Submitting new features and patches to AREDN

The high level steps to submit to this repository https://github.com/aredn/aredn are:

  1. create a github account and 'fork' this repo
  2. git commit a change into your fork, e.g. http://github.com/ae6xe/aredn
  3. create a pull request for http://github.com/aredn/aredn to consider your change